6004-2Z-SKF - Deep groove ball bearing - 6004 2z bearing

These suffixes mean "with 1 or 2 rubber seals". At 123Roulement, we use the number "2" to specify when the bearing is sealed on both sides.

Means "increased internal clearance". Often referred to as high-speed, this means that the bearing is designed for high rotational speeds and moderately high temperatures. CAUTION: a bearing with increased internal clearance will not operate optimally at low speeds. Please refer to the data sheet for the bearing you are looking for to find out its rotation speed limit.

A stainless steel bearing is generally magnetizable, as it is made from AISI 420 stainless steel, which is harder and more shock-resistant than standard stainless steel (AISI 304).To check whether your bearing is made of stainless steel, simply read the reference engraved on the side of the bearing. This reference should begin with the prefix "S" meaning "Stainless Steel".

Suitable for predominantly radial loads:- The balls are in contact with the raceways at one point only. Under purely radial load, the contact points between the rolling elements and raceways lie at the centre of the raceway. As a result, the connection between the contact points passes through the radial plane, i.e. the optimum load direction is a pure radial load.

This suffix indicates that the bearing is designed for very high operating temperatures. In general, the temperature is indicated after this suffix.Beware, these bearings are not suitable for all applications, and will require a high temperature for optimum service life.

These suffixes mean "with 1 or 2 sheet metal deflectors", for dust-tightness. At 123Roulement, we specify whether the bearing is sealed on 2 sides with "ZZ".

The Deep Groove Ball Bearing, known as 6002-2Z-C3-GJN-SKF SKF, has an inner diameter of 15 mm, an outer diameter of 32 mm and a thickness of 9 mm.

In order to provide you a personalized shopping experience, our site uses cookies. By continuing to use this site, you are agreeing to our cookie policy.

Non-contact seals (For high speeds and lower requirements for sealing):- Non-contact seals are particularly suitable for applications with high speeds and high requirements for low heat generation. They are free from friction, except for a small amount of lubricant friction in the sealing gap. As a rule, non-contact seals do not undergo wear and therefore have an unlimited operating life. Deep groove ball bearings with non-contact seals on one or both sides have the suffixes RZ and 2RZ; the suffixes Z and 2Z indicate seals on one or both sides with sealing shields.

Deep groove ball bearings are versatile, self-retaining bearings. These bearings, which are of simple design, robust in operation and easy to maintain, are available in single row and double row designs and in open and sealed variants. The solid outer and inner rings have deep raceway grooves, with shoulders which are not generally interrupted by filling slots. Solid cages made from polyamide PA66 or brass, and sheet metal cages made from steel or brass, are used as standard cages. The bearings are open or sealed.

Capable of supporting axial loads in both directions:- Due to the deep raceway grooves in the bearing rings and the narrow osculation between the raceway grooves and balls, single row deep groove ball bearings can support axial loads in both directions. The axial load carrying capacity is dependent, for example, on the bearing size, the internal construction and the operating clearance. If the axial load is too high, however, this can increase the running noise and considerably reduce the operating life of the bearings.

These suffixes indicate that the cage (the part of the bearing that holds the balls apart) is made of polymer material. Usually made of glass-fiber-reinforced polyamide.

The Deep Groove Ball Bearing, known as 6002-2Z-C3-GJN-SKF SKF, has an inner diameter of 15 mm, an outer diameter of 32 mm and a thickness of 9 mm.

The Deep Groove Ball Bearing, known as 6002-2Z-C3-GJN-SKF SKF, has an inner diameter of 15 mm, an outer diameter of 32 mm and a thickness of 9 mm.

The ABEC standard is used to classify bearings according to their machining tolerance. This standard is regularly called into question because it does not include certain technologies that are important for guaranteeing proper operation, both in terms of efficiency and bearing life.123Roulement therefore makes little use of this standard.

Greased bearings are maintenance-free:- Deep groove ball bearings sealed on both sides are lubricated with a high quality lithium soap grease with a mineral oil base, which has good anti?corrosion characteristics. The grease filling is measured so that it is sufficient for the entire life of the bearing. As a result, these bearings are generally maintenance-free.

Contact seals (For lower speeds and higher requirements for sealing action):- As these seals are in contact with a defined contact pressure against their sliding surface, they provide very good sealing action against the egress of lubricant and ingress of moisture and dust. Attention must, however, be paid to the loss of energy resulting from friction at the sealing contact. Furthermore, in bearings with contact seals, the bearing speed is restricted by the permissible sliding velocity at the seal lip, i.e. the speed suitability of these bearings is lower than for open bearings or bearings with non-contact seals. Deep groove ball bearings with contact seals on one or both sides have the suffixes RS and 2RS

Some bearings are available with more or less important variants (high or low internal clearance, special grease, very high temperature, etc.). These variants are systematically indicated by prefixes and suffixes in the part number.For example, the suffix "2RS" means that the bearing is splash-proof, thanks to a sealing flange on both sides of the bearing.The suffix "C3" means that the bearing has increased internal clearance, and will require a higher operating temperature, or a higher rotation speed.