Products   /   Bearings   /   Ball Bearings   /   Deep Groove Bearings   /   Metric   /   Unshielded   /   6200 Series   /   Deep Groove Open SKF Bearing (C3) 20x47x14mm

Please note if you do not see your country listed on the checkout please email us at sales@bearingstation.co.uk and we shall be happy to send you a quotation with delivery included.

Image

The 6204/C3 Open Metric Radial Bearings (Also known as Deep Groove or Single Row Bearings) are ideal for Car and Motorbike repair, Fans and pumps. PLEASE NOTE: WEBSITE ORDERING IS CURRENTLY UNAVAILABLE. PLEASE SEND ALL ENQUIRIES TO SALES@BEARINGSTATION.CO.UK

A stainless steel bearing is generally magnetizable, as it is made from AISI 420 stainless steel, which is harder and more shock-resistant than standard stainless steel (AISI 304).To check whether your bearing is made of stainless steel, simply read the reference engraved on the side of the bearing. This reference should begin with the prefix "S" meaning "Stainless Steel".

These suffixes mean "with 1 or 2 rubber seals". At 123Roulement, we use the number "2" to specify when the bearing is sealed on both sides.

This suffix indicates that the bearing is designed for very high operating temperatures. In general, the temperature is indicated after this suffix.Beware, these bearings are not suitable for all applications, and will require a high temperature for optimum service life.

Image

Use the table below to see our carriage charge or use our handy carriage calculator on the shopping cart page as you add products.

The ABEC standard is used to classify bearings according to their machining tolerance. This standard is regularly called into question because it does not include certain technologies that are important for guaranteeing proper operation, both in terms of efficiency and bearing life.123Roulement therefore makes little use of this standard.

Bearing Station stock a full range of Bearings, Belts, Chains, Pulleys, Sprockets, Couplings, Adhesives & Sealants, Oil Seals, O Rings, Electric Motors, Link Belting, SKF Maintenance Products, Freudenberg Seals and much, much more from the world’s leading manufacturers backed up by great service, technical backup and prices for all budgets.

There are 3 main sizes you would measure when trying to identify a bearing. The Inside Diameter (ID), the Outside Diameter (OD) and the Width. The most accurate device you can use is a Vernier (As shown in the below image).

This service is available to Mainland UK addresses, however it may take a little longer for Highlands and Islands. If you are unsure please phone where we would be delighted to help.

Deep Groove Open SKF Bearing (C3) 20x47x14mm Specifications Inside Diameter : 20mm Outside Diameter: 47mm Width: 14mm Shield Type: None Brand: SKF No minimum order Quantities/Order Value

The Deep Groove Ball Bearing, known as 6202-C3 Generic, has an inner diameter of 15 mm, an outer diameter of 35 mm and a thickness of 11 mm.

The 6204/C3 Open Metric Radial Bearings (Also known as Deep Groove or Single Row Bearings) are ideal for Car and Motorbike repair, Fans and pumps. PLEASE NOTE: WEBSITE ORDERING IS CURRENTLY UNAVAILABLE. PLEASE SEND ALL ENQUIRIES TO SALES@BEARINGSTATION.CO.UK

The Deep Groove Ball Bearing, known as 6202-C3 Generic, has an inner diameter of 15 mm, an outer diameter of 35 mm and a thickness of 11 mm.

These suffixes mean "with 1 or 2 sheet metal deflectors", for dust-tightness. At 123Roulement, we specify whether the bearing is sealed on 2 sides with "ZZ".

Some bearings are available with more or less important variants (high or low internal clearance, special grease, very high temperature, etc.). These variants are systematically indicated by prefixes and suffixes in the part number.For example, the suffix "2RS" means that the bearing is splash-proof, thanks to a sealing flange on both sides of the bearing.The suffix "C3" means that the bearing has increased internal clearance, and will require a higher operating temperature, or a higher rotation speed.

These suffixes indicate that the cage (the part of the bearing that holds the balls apart) is made of polymer material. Usually made of glass-fiber-reinforced polyamide.

The Deep Groove Ball Bearing, known as 6202-C3 Generic, has an inner diameter of 15 mm, an outer diameter of 35 mm and a thickness of 11 mm.

Means "increased internal clearance". Often referred to as high-speed, this means that the bearing is designed for high rotational speeds and moderately high temperatures. CAUTION: a bearing with increased internal clearance will not operate optimally at low speeds. Please refer to the data sheet for the bearing you are looking for to find out its rotation speed limit.

All delivery times quoted are from when the goods leave ourselves.  Please note that during Christmas delivery make take a little longer due to the busy Period