Your vehicle utilizes a wheel bearing at the hub to allow the tire and rim to smoothly rotate at both low and high speeds. As a rotating part, the wheel bearing's material slowly wears down during usage.

Wheel Bearing costAutoZone

A steel shaft adapter to convert a crankshaft from 1 1/8" inch to 1 7/16" inch shaft. The adapter is approximately 4 inches long and includes the key. A very handy way to use your old pulley on a new engine.

Wheel bearingnoise

An adaptive sleeve that converts 5/8'' (15.88mm) threaded shaft to 7/8" (22mm) diameter keyway shaft.Engines with threaded shafts are usually engines that fit to water pumps, as the impellor screws onto the end of the shaft. The thread is only at the end...

A steel shaft adapter to convert a crankshaft from 1" inch to 1 1/8" inch shaft. The adapter is approximately 3 inches long and includes the key. A very handy way to use your old pulley on a new engine.

Replace wheel bearing costnear me

Let your local Meineke Car Care Center perform a diagnosis and we’ll let you know how we can repair or replace your wheel bearings to get your car back to a healthy state.

At this point, you must have a qualified technician change out the worn components using a wheel bearing press to restore your vehicle to good working condition and eliminate distressing noises and poor ride quality.

Technicians receive ample training to learn how to change wheel bearings correctly. Technicians use heavy-duty tools in the shop, including a large press, to pop the bearings out of the hub. On most vehicles, your technician must remove the tire, rotor and hub to access the bearing mounting point.

Frontwheel bearingreplacementcost

A steel shaft adapter to convert a crankshaft from 1 1/8" inch to 1 7/16" inch shaft. The adapter is approximately 3 inches long and includes the key. A very handy way to use your old pulley on a new engine.

Rearwheel bearingreplacementcost

Any time your vehicle is making unusually loud noises it’s safe to assume that something’s not right. Sometimes the culprit is your car’s wheel bearings. Wheel bearing press service, bearings replacement or other services may be required. Read below to learn about symptoms of problematic wheel bearings and replacement services.

Wheel bearingreplacement near me

After placing the hub in the press, it takes several minutes to change the wheel bearings. Your new bearings must also be pressed into the hub to seat their rear surface at the correct point.

A steel shaft adapter to convert a crankshaft from 3/4 to 1 inch shaft. The adapter is approximately 4 inches long and includes the step key needed to go from the 1/4 in key way to the 3/16 key way. A very handy way to use your old pulley on a new...

At first, bad wheel bearings will start to squeak loudly while you drive. You will know it is time to replace the wheel bearing if the noise is constant, not just when you press the brakes.

Frontwheel bearingreplacementcostNear me

A steel shaft adapter to convert a crankshaft from 3/4 to 1 inch shaft. The adapter is approximately 3 inches long and includes the step key needed to go from the 1/4 in key way to the 3/16 key way. A very handy way to use your old pulley on a new...

A steel shaft adapter to convert a crankshaft from 1" inch to 1 1/8" inch shaft. The adapter is approximately 4 inches long and includes the key. A very handy way to use your old pulley on a new engine.

In many cases, the diagnostic process will quickly pinpoint the front wheel bearings as the cause. Upon confirming the diagnosis, a technician will write up a work order that includes the total cost to replace your wheel bearings.

In order to understand the big picture and repair your vehicle properly, technicians must check wear on a variety of components from tires and brakes to tie rods and control arms to find the source of the noise and vibrations.

An adaptive sleeve that converts V-twin 7/8" tapered shaft engines into a 1 7/16" diameter keyway shaft. Keyway is 3/8" Key Is Not IncludedFits:Honda GX630 / GX660 / GX690 'V' spec enginesKohler CH620 / CH680 / CH730 / CH740 and all other v-twin taper...

Replace wheel bearing costcalculator

A steel shaft adapter to convert a crankshaft from 7/8" inch to 1" inch shaft. The adapter is approximately 3 inches long and includes the key. A very handy way to use your old pulley on a new engine.

The key to keeping any small engine or motor running smoothly is providing maintenance and replacement parts when necessary. We carry all the small engine repair parts you need for regular maintenance and high-performance upgrades. Shop around to find the small engine parts for your equipment or contact us for help finding exactly what you need before you buy.

A steel shaft adapter to convert a crankshaft from 1" inch to 1 7/16" inch shaft. The adapter is approximately 4 inches long and includes the key. A very handy way to use your old pulley on a new engine!

A steel shaft adapter to convert a crankshaft from 5/8 to 3/4 inch shaft. The adapter is approximately 3 inches long and includes the key. A very handy way to use your old pulley on a new engine.

Upon completing the service, the technician will take your vehicle for a test drive to check the noise levels and ride quality. If all goes well, you will then have your vehicle returned to you.