Cost of replacing a rear wheel bearingnear me

The outer bearing should fall out easily, whereas the inner bearing will require the seal to first be removed - using a seal puller or a flathead screwdriver.

In general, you may expect to invest $190 to $310 for parts associated with the rear bearing replacements. Meanwhile, the labor charges fluctuate from $250 to $400.

Cost of replacing a rear wheel bearingtoyota

Use a ratchet to unbolt brackets and brake calipers from the spindles. Once done, remove the calipers with a screwdriver.

Block the tires opposite your chosen wheel using a chock. For illustration, if you change the front bearings from the driver’s side, then remember to chock the rear wheels from the passenger’s.

Jiffy Lubewheel bearingreplacementcost

Put your new bearings into the rotor’s back and apply some grease to the cavity’s interior. Next, install the new seals over the bearing before placing the new retaining nuts on their spindles.

Position the race on the hub, and hit the back of the handle with a hammer - to seat the bearing race all the way down into the hub. The collars are constructed of 6061 aluminium, which is softer than the bearing race to prevent damage, but still hard enough to stand up to regular use.

Now that the vehicle is safely secured and lifted, you can proceed to remove the nuts completely. Once done, pull the tires off and place them aside.

To save you hours of research, my team has compiled the average price range of some of the most commonly-asked cars. If yours does not make its way into this list, I suggest consulting your dealer or manufacturer.

To make your job even easier, the collars in the race driver kit can be used with the SCA 6000 Kilogram Shop Press, allowing you precise control when installing bearing races and seals.

Technically, you can, but it’s extremely dangerous. Premature/ uneven tire wear, worn transmission, and even explosions are inevitable.

Frontwheel bearingreplacementcost

Start by parking your vehicle, or in this case – trailer – on a level surface. Jack up the wheel being worked on, support the axle using a rated stand – and remove the hubs by following a workshop manual.

Locate the rotor faces and place them face down on the ground (the back facing upwards). Then take your new bearing and push its bearing greases into your casing.

Wheel Bearing costAutoZone

Once gathering the required supplies, you should prep the car beforehand to ensure maximum safety. To begin, park the vehicle on an even, level surface.

Mechanic experts will have specialized tools to help press out those old bearings for you. After the new bearings are pressed in, technicians will re-install the spindles onto the vehicle.

Does the bearing stay flush against the spindle? If so, I suggest removing the spindles – then taking both the bearings and spindles to the nearest repair shop.

Subaruwheel bearingreplacementcost

A wheel bearing is often stored within the disc brake rotors, meaning you have to pry the dust cap off to expose retaining nuts and cotter pins. A couple of pliers will be your trusted ally in such cases.

Replacing wheel bearings is a piece of cake and can save quite a few bucks, guaranteed you ALREADY have all these tools at home:

Not to mention, not everyone is familiar with the technical aspects of the vehicle; jumping blindly into it without proper research might end up costing you even more than it should have.

While driving to mechanics is more convenient and also time-saving, feel free to replace the bearings at home if you already have all the required tools ready. Write me letters if any type of wheel bearing issues persist

For driving seals into place, use the flat side of the tool which closest matches the outer diameter of your seal. Apply a little grease; and drive it into the hub using the same technique as with the bearing race.

If you want to play on the safer side and replace every bearing, expect to spend between $800 and $1000 in total. Unless you are already covered by special warranty policies, the overall costs can be quite a blow for most vehicle owners.

There are 9 different sized collars in the Bearing Race and Seal Driver set, to suit most wheel bearing sizes. Choosing the right one for the job is as simple as sliding a new bearing race over the tapered end of the collars - until you find the one with the best fit.

Wheel bearingreplacement near me

Loosen them with a ratchet (1/2 inches) and proper size sockets. Remember just to loosen them; don’t remove the nuts completely yet.

Hence, I often try to save the cost of wheel bearing by fixing/ swapping only one bearing. It is much cheaper than simultaneous front/rear replacements (refer to the pricing section above) while still delivering impeccable performance.

There is no point in choosing to do it on your own if these tools have not yet been purchased; buying all of these equipment pieces in one go can be even pricier than having it done by auto mechanics.

Regular wheel maintenance schedules should include frequent wheel bearing checks; that has always been a rule of thumb. However, it is the cost to replace wheel bearings that gives people a headache, as they are uncertain whether these upgrades may give huge blows to the financial budgets.

Unfortunately, the front wheel bearing replacement cost is much more expensive than its rear counterparts. The average labor cost runs from $350 to $550, while the pricing for replacement parts is $150 to $300.

Lift the car off the ground with two jack stands. That way, you will find it easier to remove the tire for ball bearing replacements.

Once all of the bearings are out, give the hub a good clean - mount it firmly in a bench vice, and drive the old bearing races out using a punch. Most hub assemblies have a relief cast into them, to allow the punch a proper purchase on the bearing race.

Cost of replacing a rear wheel bearingcalculator

Douglas Mercer is an automotive service manager with 12-year experience at Stockton Wheel Service, Douglas excels in addressing intricate tire and wheel concerns as plating wheels, straightening bent wheels, widening stock wheels, and precisely correcting offset and back-spacing…

Your browser's Javascript functionality is turned off. Please turn it on so that you can experience the full capabilities of this site.

Yes. Since wheel bearings and brake rotors are aligned, failed bearings will loosen the brake rotors and cause violent wobbles.

The average pricing range can stoop as low as $107-$147 (DIY) to as high as $400-$1000 (mechanic) – depending on whether you prefer DIY procedures or mechanic supports.

My insightful guide, while not offering direct solutions to your budget-saving goal, can still deliver helpful advice regarding the cost and alternative replacement methods. Keep scrolling.

The ToolPRO Bearing Race and Seal Driver kit will help you get the job done properly - without damaging your brand new parts.

Before inserting the new race, clean the area up with a clean rag, and use a wire brush to remove any stubborn grime or corrosion.