BR25 flight status

Designed with a long, flexible lip, the V-ring can act as a face seal, a lip seal or slinger. The construction is three part: the body (a), the conical self-adjusting lip (b) and the hinge (c). The elastic body holds itself in place on the rotating shaft while dynamic sealing takes place where the lip is in axial contact with the counterface. The counterface should be metal and can be the end of a gearbox housing, a washer, a suitable steel stamping, even the back of an oil seal. Generally no seal bore is required and no shaft preparation is needed.

V-ring seals are available in a large variety of designs and sizes to fit the requirements of most applications. V-rings are normally made of nitrile rubber. For applications where higher temperatures occur or where aggressive media are present, V-rings made of fluoro rubber should be used.

In addition to highly effective contaminant exclusion, Vrings can be used to retain grease lubricants. However, with proper countersurface preparation they can run dry with very low torque loss and good service life. Because the V-ring is very elastic (smaller V-rings can be stretched up to 2 1/2 times their free diameter) it can often be easily fitted to shafts without disassembly of the unit—even over flanges, pillow blocks, or other assemblies. One size V-ring can be used on a number of shaft sizes either English or metric dimension. Less than 142 sizes covers a wide range of shaft sizes from .110" (2.7mm) to 29' (9000mm). Sizes up to 79.530" (2020mm) and beyond are available in nitrile or fluoroelastomer (Viton™) covering a wide variety of media compatibility in temperature ranges from -40°F to 212°F (nitrile) and -15°F to 392°F fluoroelastomer.

V-rings are normally made of nitrile rubber that features good chemical resistance, resistance to wear and can be used in applications with normal operating temperatures. For applications with higher temperatures or where aggressive media are present, V-rings made of fluoro rubber can be supplied. The permissible operating conditions for V-rings made of nitrile or fluoro rubber are listed in the table. In the product table under the heading "Lip code", the letters R and V are used to identify nitrile rubber and fluoro rubber respectively.

BR27

Image

Please be advised that Industry Kitchens will require a 10% refundable holding deposit to secure your order. This 10% is fully refundable. You will receive this refund after the goods have been delivered. Please note that this 10% deposit is separate from any fees Silverchef requires.

BR26seat map

VR5 A heavy-duty large diameter style designed to operate in the severe conditions found in metals and paper mills. The unique body profile can accommodate radial and axial support in high shaft speeds applications. It has an extension that can be fitted into mechanical components or trimmed to length to meet existing space requirements (contact SKF for details). Available for shaft diameters from 11.811" (300mm) to over 78" (2000mm) in nitrile and fluoroelastomer on a made-toorder basis.

BR261

VR6 This heavy-duty profile is also designed primarily for protecting high speed bearing arrangements in rolling mills, papermaking and large machine applications. It should especially be considered for new equipment designs. The shape is similar to the VR5 except it does not have the extension to the rear of the body section, allowing a narrower B1. It does retain the saddle feature for axial and radial location on the shaft with a specially designed clamping band. The key installation dimensions are the same as the VR4 except for the body height. Available on a made to order basis in both nitrile and fluoroelastomer for shafts from 11.811" (300mm) to over 78" (2000mm).

Terms and conditions apply – refer to the product Instruction Manual for specific warranty details relating to your machine.

Noaw slicers carry 2 years warranty and Vitamix blenders carry 1-year parts and labour warranty followed by a further 2 years parts only warranty.

BR261 flight status

BR26flight Status today

VR2 The original V-ring designed with a wide body and tapered heel to firmly hold the ring on the shaft. Available in sizes from .180" (4.5mm) shaft to 8.270" (210mm). Commonly used in agricultural and automotive applications.

VR4 A heavy-duty large diameter style commonly used in rolling mills as a secondary seal for heavy duty applications where the primary seal has to be protected against water and or particulate contamination. VR4 is the preferred heavy duty V-ring in replacement applications. Selected sizes are in stock and others can be made to order. For new designs, the VR6 should be considered and has similar mounting dimensions. Available in both nitrile and fluoroelastomer for shafts from 11.811" (300mm) to over 78" (2000mm).

The V-ring is an all-rubber seal available from All Seals.It is mounted directly on the shaft by hand and seals against a counterface. This unique design has been extensively used on a broad range of applications.

BR28

Image

You're entitled to a replacement or a refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if they fail to be of acceptable quality and the failure does not constitute a major failure.

BR25

Specific warranty details and exclusions are included with every machine sold. Typically, items such as glass, lamps and non-stick coatings are not covered under warranty.

The rental agreement commences on the day of installation and your first payment will be deducted 7 days after delivery. The Silver Chef rental agreement term is a 12-month contract, but you do have the option to purchase the products at any time and you will receive a 75% rental rebate, excluding GST. You also have the option to upgrade anytime in the same category or return the goods after 12 months if no longer required.

Image

All Australian warranty work is to be authorised and handled by the warranty department by filling in the form on the Roband website or phoning 1800 268 848

VR1 The most common style available in the widest range of sizes from .110" (2.7mm) shaft to 79.530" (2020mm) nitrile and fluoroelastomer. Ideal for protecting gearboxes, electric motors and drives.

VR3 Very compact axial cross-section commonly used in confined spaces to replace labyrinth seals. Available in nitrile and fluoroelastomer for shaft sizes from 4.134" (105mm) shaft to 78.745" (2000mm) and beyond.