Hard faced mechanical seals are typically used when the fluid handled may be harsh, and contain solids. Such seals are usually made in Silicone Carbide or Tungsten Carbide due to its hard wearing construction it is built to withstand unexpected small solids such as Sand, dirt, stone and is a great choice for heavy duty applications.

Life adjustment factors allow the original equipment manufacturer to better predict the actual service lives and reliability of bearings that you select and install in your equipment.  An adjusted calculated L10 rating life is calculated by using the following formula:

If you are unable to find the product that you are looking for then please contact us via sales@northridgepumps.com or call +44 (0) 1773 302 660

Cartridge seal - When a mechanical seal is first inserted within a pump its clearances should be set. By utilising a cartridge clearances do not need to be set as the unit is pre-assembled eliminating the need for time-consuming assembly and spring setting on site.

Requires slight leakage to ensure packing   is cooled. Over time leakage increases. Leakage causes secondary issues such   as slip or trip hazards, extra cleaning and disposal costs.

Pmin = required minimum equivalent load on the bearing, radial load for radial bearings and thrust load for thrust bearings.

Most machines employ two or more bearings on a shaft, and often there are two or more shafts. All of the bearings in a machine are then considered to be a bearing system.  For business purposes, it is important for the manufacturer to know the reliability or system life of their machine.  This evaluation process considers the importance of combining the L10 lives of all the bearings in the system to answer the question, “How long will the machine perform with 90 percent reliability?” In simpler terms, the system L10 reliability will be less than the lowest individual L10 rating life. The following formula is used to calculate the System Rating Life:

Double mechanical seal - This is where two mechanical seals are used within a pump. The first seal retains the fluid within the pump as per the standard mechanical seal above. The second seal contains a barrier fluid to ensure the faces are kept clean and are lubricated preventing failure. Without such liquid, the mechanical seals would run dry and fail.

Automotiveseal type

For over 100 years, we have been engineering, designing and building solutions that meet and exceed customer’s requirements for standard and specialty bearings.

Rubbersealtypes

American Roller Bearing Company primarily makes heavy duty industrial class bearings that are used in various industries in the US and around the world.

Generally, misalignment is not a good thing for rolling element bearings that are not specifically designed to accommodate misalignment. Ball, tapered and cylindrical roller bearing capacity is based on the assumption that the misalignment will not exceed 0.0005 radians (0.03°).  Misalignment greater than this will lead to L10 lives less than that calculated.

“Rating life” is the bearing life calculated for 90% reliability.  This is the amount of time that a group of apparently identical bearings will complete or exceed before the formation of a fatigue spall. The basic formula for calculating bearing L10 rating life is:

Employing Finite Element Analysis (FEA) of the shaft and housing under load can predict the amount of distortion that will occur. A computer analysis of the internal workings of the bearing can show the stress distribution. Next, optimized roller crowning can be applied to minimize the reduction in bearing life. Consult American’s sales department if the effect of distortion needs to be included in the calculation of bearing life.

Once the loads and speeds have been determined, the question now becomes, “How many hours of rating life are needed for a well-designed machine?” Sometimes, this is spelled out either by specific industry standards or company policy based on the industry and customer expectations. It may be perfectly acceptable in one industry for the end-user to overhaul their equipment, replacing bearings, seals, etc. once every year. In another industry, it may be expected that the bearings last ten years minimum. Also to be taken into consideration when determining the value of the minimum desired rating life is how often the equipment is in use. Does it run intermittently or full time during a work shift? How many shifts per day and how many days per week?

Some applications produce very high radial and thrust loads, and it might not be physically possible or feasible to use a single bearing that is capable of taking both types of load. In such situations, a better design is to provide separate bearings to take the radial and thrust loads. When this occurs, the machine designer must be careful to ensure that the radial bearing takes only the radial load, and the thrust bearing takes only the thrust load.  A good way to accomplish this is to use a cylindrical roller bearing with one straight race at the “radial” location, as this bearing cannot take any thrust.  A pair of angular contact bearings or steep angled tapered roller bearings is often a good choice to take the thrust load, but they must be prevented from seeing any radial load. One way to accomplish this is to make the fit of the outer races very loose in their housings: typically .5 mm/.020 In. to 1.0 mm/.040 In.

Types of seals engineering

In most applications, the existing weight of the shaft, gears, couplings, etc. is sufficient to exceed the Minimum Bearing Load.  However, during startup, the angular acceleration of the shaft should be monitored and limited to insure that the bearings immediately start rolling as the shaft starts to rotate.

A review of the standard bearing tables will reveal that for any given bore diameter, several bearings are available with increasing O.D.s and widths. Section heights and capacities increase accordingly. Section height is simply the radial dimension between a bearing’s bore and its outside diameter, into which must be fitted an inner race, balls or rollers, and an outer race. A properly designed bearing balances the thicknesses of the two races with the rolling element diameter in order to optimize Dynamic Capacity without significantly reducing the structural strength of the races. Bearings with thinner races are more subject to distortion than those with thicker cross-sections and thicker races.

All ball bearings, tapered roller bearings, and spherical roller bearings are capable of taking a significant axial thrust load. The “equivalent bearing load”, P, used in the rating life formula, needs to be calculated when combined radial and axial loads occur. This calculation can be somewhat complicated as it depends on the relative magnitudes of the radial and thrust loads to each other and the contact angle developed by the bearing. It would be too difficult to show all the methods of calculating P for all the bearing types shown. For tapered roller bearings, the “K” thrust factor is employed. For any application needing a rating life calculation with combined radial and thrust loading, please contact American’s sales department.

If you are unable to find the product that you are looking for then please contact us via sales@northridgepumps.com or call +44 (0) 1773 302 660

However once rotation stops, so does the dynamic sealing meaning a seal must be in place to prevent media leaking. This can be done by either external flush, packing, lip seals or an inflatable bellows. An expeller seal is useful for slurry pumps used within mines at remote locations where a seal flush is required, which consume vast amounts of water. As water is scarce, and expensive in such areas sizeable savings can be made by switching to such a sealing arrangement.

Seal typePokémon

Typically Mechanical seals are usually manufactured in Carbon Ceramic, with a Stainless Steel Spring. Carbon is a good general choice for the majority of applications where a fluid is compatible, not contaminated and fairly clean.

American Roller Bearing Company primarily makes heavy duty industrial class bearings that are used in various industries in the US and around the world.

Seal typeanimal

O ring - A circular cross-section seal used on casings, around valves and other small valves which forms a seal around the periphery of the object.

Single mechanical seal - this is the most common seal type used which is a seal used to seal the pump head, ensuring the liquid is retained within the pump head and does not leak out via the back of the pump casing where entry is made via the shaft which is driven by a motor. The seal consists of several parts involving a rotating assembly which rotates as the shaft rotates, a stationary part which is fixed and is cooled by the liquid being pumped, and a spring to ensure the seal remains compressed and most importantly airtight.

In general, for a bearing to properly operate, the inner and outer races must be properly supported by the shaft and housing. However, the nature of the design of some types of equipment does not always allow this. As discussed in the misalignment section, sometimes significant shaft deflection can occur causing misalignment. Housings can distort under relatively heavy loads and allow the bearing’s outer race to distort in the same manner. All of these effects tend to reduce the theoretical life of the bearing, but with proper analysis and special internal design, this reduction can be minimized.

Requires replacement more often adding   to wear and tear of pumps as they are assembled and disassembled. More labour   intensive

The best bearing for a float location is a cylindrical roller bearing with one straight race. Axial float is easily accommodated by the lubricated rollers sliding on the straight roller path. If another type of bearing is used, such as a deep groove ball bearing, double row angular contact bearing, TDO tapered roller bearing or spherical roller bearing, the typical practice is to allow the outer races of these bearings to slide in the housing bore.

North Ridge Pumps Ltd are an independent manufacturer and distributor of pumps. Established since 1998, we have a wealth of experience in pumping applications, handling fluids from freshwater, seawater and glycols to heavy oil, grease, food and chemicals. Having worked in a variety of demanding industries both in the UK and Internationally, any fluid you can think of, we have most likely pumped it.

Registered Business Address: 12 Bridgford Road, West Bridgford, Nottinghamshire NG2 6AB - Registered in England & Wales 03652700

More forgiving than mechanical seals, accepting particles, and large shaft movements such as in the Paper & Mining Industry. Can continue to be used even when pump has experienced excessive   wear.

The Bearing Static Capacity, Co, is the maximum load that can safely be applied to a non-rotating bearing that will not cause subsequent bearing operation to be impaired. It is based on calculated contact stress at the center of the most heavily loaded rolling element where it contacts the Inner Race. These stress levels for three types of bearings are:

In many cases involving bearing selection during the initial design of a machine, obtaining a satisfactory rating life is the prime consideration. The shaft size is usually decided first, based on allowable working stress and deflection. This establishes the bearing bores. Fortunately for the equipment designer, standard bearings can be found with different O.D.s and widths for a given bore size. As the bearing envelope volume increases with O.D. and width, dynamic capacity increases accordingly, yielding increased rating life.

Mechanicalsealtypes PDF

Packed gland - A packed gland is when a braided material which has an appearance similar to a flat rope is wrapped around a shaft. A packed gland is also known as stuffing as the packed gland is typically wrapped tight around the shaft and inserted within a chamber known as a stuffing box. Packed glands must leak a little to allow cooling from immediate contact with the shaft to prevent burning, and over time do wear shafts. Packed glands were used more historically as they were utilised before mechanical seals were invented. They are still used in some boiler feed pumps where seal failure is common from overheating, cavitation or the presence of high fine solid content is expected as it is a cheap way to seal the pump rather than utilising expensive flushing liquids or double mechanical seals such as in dredging.

The Bearing Dynamic Capacity formula was empirically determined through carefully controlled laboratory life testing. Many bearing applications are far from laboratory conditions. Therefore it can be difficult to justify an a3 factor greater than 1.0. Conditions such as high temperature, contamination, exterior vibration, etc. will lead to an a3 factor less than 1. If the lubrication is superior and the operating speed high enough, a significantly improved lube film can develop between the bearing’s internal contact surfaces justifying an a3 factor greater than 1.0.  To safely use this benefit for design or commercial reasons requires a thorough analysis and either test data or previous experience.

In the OEM’s process of predicting the service reliability of his/her equipment, it is sometimes necessary to increase the reliability of the selected bearings to predict a longer mean time between failures. The a1 factors shown below are for increased values of reliability.  If a lower value for L10 is calculated with an a1 factor, and it is not acceptable, then a bearing with greater Dynamic Capacity needs to be chosen.

Stampsealtypes

Spherical roller bearings and self-aligning thrust bearings are specifically designed to accommodate misalignment.   Self-aligning cylindrical roller bearings can also accommodate some misalignment these bearings. This type of bearing is found in the "Custom" bearings section. These special bearing types can accommodate misalignments from 1.0° to 1.5°.

North Ridge Pumps Ltd are an independent manufacturer and distributor of pumps. Established since 1998, we have a wealth of experience in pumping applications, handling fluids from freshwater, seawater and glycols to heavy oil, grease, food and chemicals. Having worked in a variety of demanding industries both in the UK and Internationally, any fluid you can think of, we have most likely pumped it.

Many applications do not operate at a constant load or speed, and to select bearings for a certain rating life in hours based on the worst operating condition might prove uneconomical.  Often, a duty cycle can be defined for the various operating conditions (load and speed) and the percentage of time at each.  A related situation also occurs in some machines that create a reciprocating motion.  In such instances, a complete duty cycle occurs within one revolution of the bearing.  Furthermore, the two examples could be combined for several anticipated operating conditions with reciprocating motion and different peak loads and speeds. Calculating the rating life when loads and speeds vary involves first calculating the L10 rating life at each operating condition of the duty cycle.  Next, the formula below is used to combine the individual L10 lives to a rating life for the complete duty cycle.

There have been many improvements in bearing design and manufacture over the years that have been proven in life tests that result in improved L10 rating life. Some of these improvements are:

It has been learned from experience that bearings require a minimum applied load to insure traction for the rolling elements so they roll as the shaft starts to rotate. If the balls or rollers do not roll, they will skid on the moving raceway, wiping away the lubricating oil, and causing damage to the rolling element O.D.s and raceway surfaces. This is called “skidding” and the resultant damage is referred to as “smearing”, which will shorten bearing life.

When a bearing does not make a complete rotation but oscillates back and forth in operation, a lower equivalent radial load can be calculated using the formula below:

American Roller Bearing primarily makes heavy duty bearings that are used in various industries in the US and around the world. Not only must our industrial class bearings provide long in-service life from a rolling fatigue criterion, but they must also hold together structurally from impacts, overloads, and occasional high-speed excursions. The design of every heavy-duty bearing has been optimized to this end, including our large bore bearings.

Most bearing systems employ two or three bearings in order to support a shaft under radial and thrust loads. The number of bearings depends on whether one bearing is also capable of taking a thrust load. In cases where the thrust load is negligible, one bearing should be a considered a “locating” bearing that positively positions the shaft. When there is a significant distance between two support bearings, differences in thermal growth between the shaft and the housing require that one bearing be the locating or thrust bearing and the other be a “float” bearing. Also, a stack-up of axial tolerances between the two bearing locations needs to have one bearing “float” axially so that a parasitic thrust load is not created.

Radial cylindrical roller bearings that have opposing flanges on their inner and outer races have a limited capability of taking a thrust load though the length of the rollers. It is so limited that we do not recommend users intentionally do this.  Acceptable thrust loading is using roller ends and flanges for intermittent thrust and locating purposes. Since any thrust load would be perpendicular to the radial load and would use different bearing contact surfaces, it is not a factor in the bearing’s life calculation.

The bearing Dynamic Capacity, C, is defined as the constant stationary radial load which a rolling bearing can theoretically endure for a basic rating life of one million revolutions. Values for this important bearing parameter, C, are shown in each bearing table except Crane Hook bearings.  Bearing dynamic capacity is used to predict a rating life for each bearing at its anticipated loading and rotational speed.  Generally, a bearing should only be subject to a maximum operating load equal to half its Bearing dynamic capacity. The method of calculating bearing dynamic capacity has been defined by associations such as the American Bearing Manufacturers Association (ABMA) and the International Organization for Standardization (ISO). The formulas use the internal dimensions of the bearing raceways and their rolling elements.

Bearing Dynamic and Static Capacities are reduced at high operating temperatures. The basic reason is the reduction of raceway and rolling element hardness at high temperatures. Bearing Dynamic Capacity should be reduced by multiplying  the reduction factors as shown below. The temperatures shown are those of the bearing components themselves, which are usually higher than the ambient temperature of the application.

Lip seal - A seal which fixes around rotary parts to retain lubricants retain pressure and separate fluid from the atmosphere.

Types of seals in pumps

Seal Quench - A seal quench is where pipework is connected to a mechanical seal to allow cooling when high-temperature liquids are pumped. Seal quenches can use freshwater for cooling, but also barrier fluids for keeping the mechanical seal faces clean when abrasive liquids are pumped.

Do you require replacement mechanical seals and gaskets? Suffering from frequent seal failure or replacement? We can help diagnose the cause and eliminate recurring failures.

Expeller Seal - An Expeller seal is a shaft sealing arrangement where a rotating part called an expeller is mounted where gland packing or a mechanical seal is normally fitted. Its appearance is similar to that of another impeller, with rigid vanes mounted on the rear of a disc, which as it rotates reduces shaft pressure creating a dry seal around the shaft without a gasket or packing.