How to removerear axleshaft

* Use our part lookup to find out if BCA Axle Shaft Repair Bearings are available for your application here: https://bcabearings.com/catalog/search/

RETRACTABLE METRIC TAPER GAGE1 to 9 mm Metric Taper Gauge for measuring ID of tubing, slot widths, hole sizes and flange face to face dimensions. Gauge retracts safely into it’s plastic case. .Stainless steel.  0.1 graduations are accurate within 0.05mm

Rear axle bearing replacementcost

METRIC TAPER GAGE 1TG7001-15Metric Taper Gauge 1 to 15 mm on front. A 120 mm rule with a diameter correction table on the reverse side. Use the width of taper gage to measure gap. Great for measuring gaps, slot widths, hole or bore sizes and flange face to face dimensions. Stainless steel 0.1 graduations are accurate within 0.05mm

Rear Axle Bearingand Seal Kit

Image

Generally, this type of wear necessitates the replacement of the axle shafts when replacing the bearing and seal. Failure to do so can result in premature failure of the new bearing and seal, which can cause additional damage to the axle, and even damage the differential due to fluid loss.

Rear axle bearinginstallation Tool

Image

SOLUTION: BCA Axle Shaft Repair Bearings (NBRP Part Numbers) can be used to replace the OE bearing and seal without requiring replacement of the worn axle shaft. Axle Shaft Repair Bearings feature a unitized design incorporating the bearing and seal into a single component. The design of repair bearings shifts the position of the bearing and seal along the axle shaft, allowing for unworn sections of the axle shaft to be the new points of contact.

Image

Rear axle bearingremoval Tool

METRIC TAPER GAGE & RULER COMBO - STAINLESS STEEL1 to 15 mm Metric Taper Gage for measuring ID of tubing, bore, slot widths, hole sizes and flange face to face dimensions. Folds safely w/ pocket clip.- Stainless steel 0.1 graduations are accurate within 0.05mm

How to removerear axle bearingwithout puller

METRIC TAPER GAGE & 120 mm RULE IN ONEStainless Steel 1-15 mm taper gage on front side and 120 mm rule plus diameter correction table on reverse side. Use the width of taper gage to measure gap. Permanently attached handle locks into the heavy plastic case, provided with pocket clip, to keep gage and pockets from damage. All the features of the combo set in a convenient one piece metric taper gage.

PLASTIC METRIC TAPER GAUGE & RULER COMBOWill not damage surfaces, excellent for measuring slot widths and face to face dimensions.     0.1 mm graduations are accurate within 0.05 mm.  Flexible plastic ruler measures in 1.0 mm graduations. The taper gage is available in a thickness of 1/8” RIGID or 1/16” FLEXIBLE.

PLASTIC METRIC TAPER GAUGE 1 - 15mm Will not damage painted surfaces excellent for measuring ID of slot widths and face to face dimensions.  Available in  0.1mm or 0.5mm graduations. These gages are accurate within 0.05mm. Plastic taper gage for nondestructive applications.  These taper gages come standard in a thickness of 1/8” RIGID PLASTIC but are available in 1/16” FLEXIBLE PLASTIC upon request.

Rear Axle BearingInstaller

BENT GO-NO GO METRIC FEELER PLUG GAGES Plug gages are bent to 135 degrees to allow inspection and checking of fixtures in tight areas. These bent go- no go plug gages are not intended to measure angles. The plug gages are bent to allow access in tight areas. Go Nogo Sizes are available .22 mm to 4.00 mm.  Standard sizes available also.   CALL FOR QUOTE

The graduations on these high quality metric taper gauges are engraved or "etched" to ensure permanent markings. The black filled markings are on a hard chrome matte finish which reduces glare and gives you a sharp, accurate and easy to read taper gage. The graduations on other inexpensive metric gauges are often screen printed or on a polished finish which makes them hard to read, less accurate and will wear off the gage over time. Although these gages are referred to as a taper gage, they do not measure tapers.

THIS METRIC GAGE IS SOMETIMES CALLED A GAP GAGE, WEDGE GAGE OR GAP FEELERSIT IS ACCURATELY TAPERED THROUGHOUT ITS ENTIRE LENGTH FOR QUICK MEASURING,

TECH ISSUE: The OE wheel bearing design for these applications are engineered with separate bearing and seal components. Over time, the OE-designed wheel bearing and seal can wear grooves into the axle shaft at the points of contact. This leads to pitting on the axle shaft which can cause noisy operation and bearing failure, and can also cause differential fluid to leak onto the backing plate and brakes.

METRIC TAPER GAGE & RULER COMBO - STAINLESS STEEL1 to 15 mm Metric Taper Gauge for measuring slot and gap widths, hole sizes and flange face to face dimensions. Handy depth gage on ruler. Back of taper gauge is printed with diameter correction table Handy when checking holes. Made of Stainless Steel.  0.1 graduations are accurate within 0.05mm