Step 3. Elimination of parallel misalignmentMove one of the pulleys on its shaft until the laser line exactly matches the three reference lines (as per figure 15).

The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.

AR-12912 is a Set Item Of (1).

Power onSwitch on the laser unit by pressing the ON/OFF button.Determining the type of misalignmentThe laser line emitted from the laser unit will now appear on the receiver unit. The pattern will vary depending on the type of misalignment, as shown in figure 5, 6, 7, and 8.

Note: Refer to the user manual for detailed instructions on how to use the device for different types of alignments and how to interpret the results obtained from the device.EC Declaration of Conformity TKBA 40We, SKF MPT, Meidoornkade 14, 3992 AE Houten, The Netherlands herewith declare under our sole responsibility that the products described in these instructions for use are in accordance with the conditions of the following Directive(s): RADIO EQUIPMENT DIRECTIVE 2014/53/EU RoHS Directive (EU) 2015/863 and the harmonized standard:EN IEC 63000:2018: Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances and are in conformity with the following standards:Emission: EN 61000-6-3:2007, Immunity: EN 61000-6-2:2005, EN 61000-4-2, -3, -4, -5, -6, -11, EN 61010-1:2010 The laser is classified in accordance with the International Standard IEC-60825-1:2014, USA FDA Standard 21 CFR, Ch 1, Part 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50, dated June 24, 2007. Houten, The Netherlands, December 2022 Guillaume Dubois, Manager Quality and Compliance UK Declaration of Conformity TKBA 40 We, SKF MPT, Meidoornkade 14, 3992 AE Houten, The Netherlands herewith declare under our sole responsibility that the products described in these instructions for use, are in accordance with the conditions of the following Directive(s): Radio Equipment Regulations 2017 (2017 No. 1206) The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (2012 No. 3032) and the harmonized standard: EN IEC 63000:2018: Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances and are in conformity with the following standards: Emission: EN 61000-6-3:2007, Immunity: EN 61000-6-2:2005, EN 61000-4-2, -3, -4, -5, -6, -11, EN 61010-1:2010 The laser is classified in accordance with the International Standard IEC-60825-1:2014, USA FDA Standard 21 CFR, Ch 1, Part 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50, dated June 24, 2007. The person authorised to compile the technical documentation on behalf of the manufacturer is SKF (U.K.) Limited, 2 Canada Close, Banbury, Oxfordshire, OX16 2RT, GBR. Houten, The Netherlands, December 2022.Safety recommendationsAlways turn off the power of the drive machine before you start working.Always read and follow the operating instructions.Although the laser diode in the laser unit has an output power of less than 1 mW, never stare directly into the laser transmitter.Never aim the laser beam into another person’s eyes.Opening the housing of the laser unit may result in hazardous light exposure and voids the warranty.Take care not to pinch your fingers when mounting the units on the pulley.The equipment should not be used in areas where there is a risk of explosion.Never expose the equipment to high humidity or direct contact with water.Have all repair work been performed by an SKF repair shop?IntroductionPrecise alignment of belt-driven machinery is essential to increase belt and pulley life, reduce vibration, and reduce energy costs. The SKF TKBA 40 Belt Alignment Tool offers an easy and accurate method to adjust the machinery so that the grooves of the V-belt pulleys are accurately aligned.Principle of operationThe TKBA 40 consists of two units that attach magnetically to the grooves of each pulley. One unit, the laser unit, emits a laser line that is projected onto the receiver unit. The receiver unit has three target areas with three reference lines, the top reference line and the two bottom reference lines. Depending on the laser pattern projected on the target area, it is possible to determine the type of misalignment and how to correct it. Belt alignment is easily performed by adjusting the moveable machine(s) until the laser line coincides with the three reference lines on the receiver unit.Vertical angle misalignmentHorizontal angle misalignmentParallel misalignmentBelt alignment toolTechnical dataTransmitter UnitType of laserRed laser diodeLaser1× Built-in class 2 laser, <1mW, 632nmLaser line length3 m at 2 m (9.8 ft at 6.6 ft)Measurement Accuracy Angular Better than 0,2°Measurement Accuracy Offset Better than 0,5 mm (0.02 in)Measurement distance50 mm to 6 000 mm (2 in to 20 ft)ControlLaser on/off switchHousing MaterialExtruded aluminiumColourSilver, blue, blackTransmitter unit dimensions70 × 74 × 61 mm (2.8 × 2.9 × 2.4 in)Transmitter unit weight320 g (0.7 lbs)Receiver UnitHousing MaterialExtruded aluminiumColourSilver, grey, blueReflector dimensionsN/AReceiver unit dimensions96 × 74 × 61 mm (3.8 × 2.9 × 2.4 in)Receiver unit weight270 g (0.6 lbs)FixturesMounting“Magnetic, groove mounted (optional side adapter TMEB A2)”V-guidesSize 1: 22 mm, short rods (3× pairs)Size 2: size 22 mm, long rods (3× pairs)Size 3: size 40 mm, short rods (3× pairs)Size 4: size 40 mm, long rods (3× pairs)Battery and PowerBattery2× AAA Alkaline type IEC LR03Operation time20 hours of continuous operationSize and WeightCarrying Case dimensions260 × 85 × 180 mm (10.3 × 3.4 × 7.0 in)The total weight (incl. case)1,3 kg (2.9 lb)Operating RequirementsOperating temperature0 to 40 °C (32 to 104 °F)Storage temperature–20 to +65 °C (–4 to +150 °F)Relative Humidity10 to 90% RH non-condensingIP ratingIP 40Calibration certificateValid for two yearsCase contents1× TKBA 40 transmitter Unit1× TKBA 40 receiver Unit2× AAA batteries4× sizes of V-guides, 3× of each size 1× printed Instructions for Use1× Calibration certificateApplication rangeInstructions for useSelecting V-guidesFour sizes of V-guides are supplied with the TKBA 40 to fit pulley grooves of most widths and types. Should you need to exchange the V-guides for the smaller or larger one, select and attach the appropriate V-guides as shown in figure 2.Attaching laser unitsThe units are provided with strong magnets and V-guides. Place the V-guides of the first unit in the groove of the first pulley and press the unit firmly until the magnet secures it to the pulley. Place the second unit in the opposite groove of the second pulley. Position both units facing each other as shown in figure 4.Power onSwitch on the laser unit by pressing the ON/OFF button.Determining the type of misalignmentThe laser line emitted from the laser unit will now appear on the receiver unit. The pattern will vary depending on the type of misalignment, as shown in figure 5, 6, 7, and 8.AlignmentBefore aligning the pulleys it is important that the pulleys are mounted correctly on the shafts and that the shafts are straight. Buckled pulleys will have a detrimental effect on the alignment quality. Adjust one (or both) pulley machine(s) step by step until the laser line hit the three reference lines of the receiver unit.Step 1. Elimination of vertical angle misalignmentPlace shims beneath the front or rear feet of the moveable machine until the laser line is parallel to the reference lines (as per figure 11).Step 2. Elimination of horizontal angle misalignmentMove the machine until the laser line is positioned equidistantly from the three reference lines, the top reference line and the two bottom reference lines (as per figure 13).Step 3. Elimination of parallel misalignmentMove one of the pulleys on its shaft until the laser line exactly matches the three reference lines (as per figure 15).Fig 15 Pulleys perfectly alignedNote: When tightening the belt, check the horizontal angle alignment and adjust if necessary.Warning: Switch OFF the laser unit and remove both units BEFORE starting the machineryTroubleshootingNo laser lineCheck that the batteries are inserted correctly in the laser unit.Replace the batteries.Make sure the optic of the laser unit is not obstructed by dirt. If necessary, clean with aLost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

Selecting V-guidesFour sizes of V-guides are supplied with the TKBA 40 to fit pulley grooves of most widths and types. Should you need to exchange the V-guides for the smaller or larger one, select and attach the appropriate V-guides as shown in figure 2.Attaching laser unitsThe units are provided with strong magnets and V-guides. Place the V-guides of the first unit in the groove of the first pulley and press the unit firmly until the magnet secures it to the pulley. Place the second unit in the opposite groove of the second pulley. Position both units facing each other as shown in figure 4.Power onSwitch on the laser unit by pressing the ON/OFF button.Determining the type of misalignmentThe laser line emitted from the laser unit will now appear on the receiver unit. The pattern will vary depending on the type of misalignment, as shown in figure 5, 6, 7, and 8.AlignmentBefore aligning the pulleys it is important that the pulleys are mounted correctly on the shafts and that the shafts are straight. Buckled pulleys will have a detrimental effect on the alignment quality. Adjust one (or both) pulley machine(s) step by step until the laser line hit the three reference lines of the receiver unit.Step 1. Elimination of vertical angle misalignmentPlace shims beneath the front or rear feet of the moveable machine until the laser line is parallel to the reference lines (as per figure 11).Step 2. Elimination of horizontal angle misalignmentMove the machine until the laser line is positioned equidistantly from the three reference lines, the top reference line and the two bottom reference lines (as per figure 13).Step 3. Elimination of parallel misalignmentMove one of the pulleys on its shaft until the laser line exactly matches the three reference lines (as per figure 15).Fig 15 Pulleys perfectly alignedNote: When tightening the belt, check the horizontal angle alignment and adjust if necessary.Warning: Switch OFF the laser unit and remove both units BEFORE starting the machineryTroubleshootingNo laser lineCheck that the batteries are inserted correctly in the laser unit.Replace the batteries.Make sure the optic of the laser unit is not obstructed by dirt. If necessary, clean with aLost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

The SKF TKBA 40 is a laser alignment tool that helps in aligning shafts and other rotating equipment. It helps in reducing machine downtime and improves the overall productivity of the equipment. The device is compact, easy to use, and can be used for both horizontal and vertical alignments.

20246000--13000,6000--13000

20241210 — The forkhead family of transcription factors belongs to the winged helix class of DNA-binding proteins. The protein encoded by this ...

Handle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.

We, SKF MPT, Meidoornkade 14, 3992 AE Houten, The Netherlands herewith declare under our sole responsibility that the products described in these instructions for use are in accordance with the conditions of the following Directive(s): RADIO EQUIPMENT DIRECTIVE 2014/53/EU RoHS Directive (EU) 2015/863 and the harmonized standard:EN IEC 63000:2018: Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances and are in conformity with the following standards:Emission: EN 61000-6-3:2007, Immunity: EN 61000-6-2:2005, EN 61000-4-2, -3, -4, -5, -6, -11, EN 61010-1:2010 The laser is classified in accordance with the International Standard IEC-60825-1:2014, USA FDA Standard 21 CFR, Ch 1, Part 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50, dated June 24, 2007. Houten, The Netherlands, December 2022 Guillaume Dubois, Manager Quality and Compliance UK Declaration of Conformity TKBA 40 We, SKF MPT, Meidoornkade 14, 3992 AE Houten, The Netherlands herewith declare under our sole responsibility that the products described in these instructions for use, are in accordance with the conditions of the following Directive(s): Radio Equipment Regulations 2017 (2017 No. 1206) The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (2012 No. 3032) and the harmonized standard: EN IEC 63000:2018: Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances and are in conformity with the following standards: Emission: EN 61000-6-3:2007, Immunity: EN 61000-6-2:2005, EN 61000-4-2, -3, -4, -5, -6, -11, EN 61010-1:2010 The laser is classified in accordance with the International Standard IEC-60825-1:2014, USA FDA Standard 21 CFR, Ch 1, Part 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50, dated June 24, 2007. The person authorised to compile the technical documentation on behalf of the manufacturer is SKF (U.K.) Limited, 2 Canada Close, Banbury, Oxfordshire, OX16 2RT, GBR. Houten, The Netherlands, December 2022.

Dutchman's Custom Alloy Street, Track, and Offroad axles are forged from the ever popular and strong 1541-H or optional 4130 Chromoly material.

But, the average life of a sealed wheel bearing and hub assembly is about 85,000 to 100,000 miles, without the opportunity for a technician to ...

Fig 15 Pulleys perfectly alignedNote: When tightening the belt, check the horizontal angle alignment and adjust if necessary.Warning: Switch OFF the laser unit and remove both units BEFORE starting the machineryTroubleshootingNo laser lineCheck that the batteries are inserted correctly in the laser unit.Replace the batteries.Make sure the optic of the laser unit is not obstructed by dirt. If necessary, clean with aLost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

The average cost of replacing a wheel bearing is £175, with prices ranging from £120 and £300. The cost will vary depending on whether the front or rear or if ...

Application rangeInstructions for useSelecting V-guidesFour sizes of V-guides are supplied with the TKBA 40 to fit pulley grooves of most widths and types. Should you need to exchange the V-guides for the smaller or larger one, select and attach the appropriate V-guides as shown in figure 2.Attaching laser unitsThe units are provided with strong magnets and V-guides. Place the V-guides of the first unit in the groove of the first pulley and press the unit firmly until the magnet secures it to the pulley. Place the second unit in the opposite groove of the second pulley. Position both units facing each other as shown in figure 4.Power onSwitch on the laser unit by pressing the ON/OFF button.Determining the type of misalignmentThe laser line emitted from the laser unit will now appear on the receiver unit. The pattern will vary depending on the type of misalignment, as shown in figure 5, 6, 7, and 8.AlignmentBefore aligning the pulleys it is important that the pulleys are mounted correctly on the shafts and that the shafts are straight. Buckled pulleys will have a detrimental effect on the alignment quality. Adjust one (or both) pulley machine(s) step by step until the laser line hit the three reference lines of the receiver unit.Step 1. Elimination of vertical angle misalignmentPlace shims beneath the front or rear feet of the moveable machine until the laser line is parallel to the reference lines (as per figure 11).Step 2. Elimination of horizontal angle misalignmentMove the machine until the laser line is positioned equidistantly from the three reference lines, the top reference line and the two bottom reference lines (as per figure 13).Step 3. Elimination of parallel misalignmentMove one of the pulleys on its shaft until the laser line exactly matches the three reference lines (as per figure 15).Fig 15 Pulleys perfectly alignedNote: When tightening the belt, check the horizontal angle alignment and adjust if necessary.Warning: Switch OFF the laser unit and remove both units BEFORE starting the machineryTroubleshootingNo laser lineCheck that the batteries are inserted correctly in the laser unit.Replace the batteries.Make sure the optic of the laser unit is not obstructed by dirt. If necessary, clean with aLost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

By all the youtube vids ive seen the sound is exactly that of a wheel bearing issue but the lack of common symptoms such as wheel play and ...

Lost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

No laser lineCheck that the batteries are inserted correctly in the laser unit.Replace the batteries.Make sure the optic of the laser unit is not obstructed by dirt. If necessary, clean with aLost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

Equip cars, trucks & SUVs with 2007 Pontiac G6 Wheel Bearing And Wheel Seal from AutoZone. Get Yours Today! We have the best products at the right price.

Oct 11, 2013 — ... AMS 5630 0.5Cu. However depending on which revision of AMS 5630 is specified, depends whether certain NDT and cleanliness requirements have ...

This website is an independent publication and is neither affiliated with nor endorsed by any of the trademark owners. The "Bluetooth®" word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The "Wi-Fi®" word mark and logos are registered trademarks owned by the Wi-Fi Alliance. Any use of these marks on this website does not imply any affiliation with or endorsement.

Precise alignment of belt-driven machinery is essential to increase belt and pulley life, reduce vibration, and reduce energy costs. The SKF TKBA 40 Belt Alignment Tool offers an easy and accurate method to adjust the machinery so that the grooves of the V-belt pulleys are accurately aligned.Principle of operationThe TKBA 40 consists of two units that attach magnetically to the grooves of each pulley. One unit, the laser unit, emits a laser line that is projected onto the receiver unit. The receiver unit has three target areas with three reference lines, the top reference line and the two bottom reference lines. Depending on the laser pattern projected on the target area, it is possible to determine the type of misalignment and how to correct it. Belt alignment is easily performed by adjusting the moveable machine(s) until the laser line coincides with the three reference lines on the receiver unit.

AlignmentBefore aligning the pulleys it is important that the pulleys are mounted correctly on the shafts and that the shafts are straight. Buckled pulleys will have a detrimental effect on the alignment quality. Adjust one (or both) pulley machine(s) step by step until the laser line hit the three reference lines of the receiver unit.Step 1. Elimination of vertical angle misalignmentPlace shims beneath the front or rear feet of the moveable machine until the laser line is parallel to the reference lines (as per figure 11).

Your email address will not be published. Required fields are marked *Comment * Name Email Website Save my name, email, and website in this browser for the next time I comment.

1× TKBA 40 receiver Unit2× AAA batteries4× sizes of V-guides, 3× of each size 1× printed Instructions for Use1× Calibration certificate

Step 2. Elimination of horizontal angle misalignmentMove the machine until the laser line is positioned equidistantly from the three reference lines, the top reference line and the two bottom reference lines (as per figure 13).Step 3. Elimination of parallel misalignmentMove one of the pulleys on its shaft until the laser line exactly matches the three reference lines (as per figure 15).Fig 15 Pulleys perfectly alignedNote: When tightening the belt, check the horizontal angle alignment and adjust if necessary.Warning: Switch OFF the laser unit and remove both units BEFORE starting the machineryTroubleshootingNo laser lineCheck that the batteries are inserted correctly in the laser unit.Replace the batteries.Make sure the optic of the laser unit is not obstructed by dirt. If necessary, clean with aLost calibrationIf for some reason, such as heavy impact, the laser unit loses its calibration, return the TKBA 40 to SKF for repair.MaintenanceHandle with careThe laser unit is equipped with sensitive optical components. Handle it with care. Keep the optic of the laser unit free from dirt.5.2 BatteriesThe laser unit is powered by two LR03 (AAA) batteries. Most LR03 (AAA) batteries can be used, including rechargeable NiCd cells, but alkaline batteries have the longest life span. Remove the batteries if the laser unit is to remain unused for an extended period.5.3 Spare part and accessory cotton cloth.DesignationDescriptionTKBA G2Set of V-guides (3 pieces of each size)TMEB A2Side adapterTDTC 1/AGeneral toolcase without inlay, size AThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.® SKF is a registered trademark of the SKF Group.© SKF Group 2022MP5220 · 2022/12Documents / ResourcesSKF TKBA 40 Belt Alignment Tool [pdf] Instruction ManualTKBA 40 Belt Alignment Tool, TKBA 40, Belt Alignment Tool, Alignment ToolReferences SKF SKF SKF MountUser ManualRelated PostsSKF TKBA 10 Belt Alignment Tools Instruction ManualSKF TKBA 10 Belt Alignment Tools Product Information SKF TKBA 10 & 20 The SKF TKBA 10 &…acoem NXA Digital Laser Based Shaft Alignment Tool User Manualacoem NXA Digital Laser Based Shaft Alignment Tool error { "error": { "message": "You exceeded your current quota,…SEALEY AK7500 Wheel Fitting and Alignment Tool InstructionsSEALEY AK7500 Wheel Fitting and Alignment Tool Thank you for purchasing a Sealey product. Manufactured to a high…Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction ManualT-8030G Belt Sander 1-3/16” X 21 1/4” Uses Sanding or Surface Prep Belts T-8030G Belt Sander OILING INSTRUCTIONS:…

Deflection Gauges (mandrels) are used to test flexible sewer pipe for out-of-roundness or deflection per ASTM specifications D3034 and F679.

Better than 0,2°Measurement Accuracy Offset Better than 0,5 mm (0.02 in)Measurement distance50 mm to 6 000 mm (2 in to 20 ft)ControlLaser on/off switchHousing MaterialExtruded aluminiumColourSilver, blue, blackTransmitter unit dimensions70 × 74 × 61 mm (2.8 × 2.9 × 2.4 in)Transmitter unit weight320 g (0.7 lbs)