We have developed a Wheel Bearing Greaser Tool that allows you to easily add grease to the bearings. Once your 1/2 shaft is out, or when you have a new bearing on your bench, simply use the Greaser Tool to push the grease into the bearing.  You can see it work: When you pump, the grease will fill the cavity and excess will be eventually evident out of the sides of the bearing, so you know it’s full.  Then, simply pull the Greaser Tool back out.

Bearingodtolerancechart

Use these as preventative maintenance on your existing bearings. If water or dirt exists in your current bearings, you may see water being evacuated when grease is being added.

Ballbearing tolerancechart

As described in Section 9-3, the characteristics / magnitude of the bearing load, temperature, mounting / dismounting methods and other conditions must be considered to choose proper fits. Past experience is also valuable. Table 9-3 shows standard fits for the metric series bearings; Tables 9-4 to 9-8 tabulate the most typical and recommended fits for different bearings types. 『Table 9-4 (1) Recommended shaft fits for radial bearings (classes 0, 6X, 6)』 『Table 9-4 (2) Recommended housing fits for radial bearings (classes 0, 6X, 6)』 『Table 9-5 (1) Recommended shaft fits for precision extra-small/miniature ball bearings (d＜10mm)』 『Table 9-5 (2) Recommended housing fits for precision extra-small/miniature ball bearings (D≦30mm)』 『Table 9-6 (1) Recommended shaft fits for metric J series tapered roller bearings』 『Table 9-6 (2) Recommended housing fits for metric J series tapered roller bearings』 『Table 9-7 (1) Recommended shaft fits for inch series tapered roller bearings』 『Table 9-7 (2) Recommended housing fits for inch series tapered roller bearings』 『Table 9-8 (1) Recommended shaft fits for thrust bearings (classes 0, 6)』 『Table 9-8 (2) Recommended housing fits for thrust bearings (classes 0, 6)』

4) Email us direct info@machinedintegrations.com   – We will need your contact information with phone number   – Year/make/model of machine   – If you are placing an order           – Full name and shipping address           – Give valid email address for invoice to be sent. You can pay the invoice by credit card.             (We also accept PayPal – please state if that is your preference)

2) IT 5 and IT 7 mean that shaft roundness tolerance, cylindricity tolerance, and other errors in terms of shape should be within the tolerance range of IT 5 and IT 7, respectively. For numerical values for standard tolerance grades IT 5 and IT 7, refer to supplementary table at end of this catalog.

SKFbearing tolerancechart pdf

We have developed a Wheel Bearing Greaser Tool that allows you to easily add grease to the bearings. Once your 1/2 shaft is out, or when you have a new bearing on your bench, simply use the Greaser Tool to push the grease into the bearing.  You can see it work: When you pump, the grease will fill the cavity and excess will be eventually evident out of the sides of the bearing, so you know it’s full.  Then, simply pull the Greaser Tool back out.

Bearingshafttolerancechart

Bearing tolerancecalculator

Use these as preventative maintenance on your existing bearings. If water or dirt exists in your current bearings, you may see water being evacuated when grease is being added.

Bearing tolerancestandard

[Remarks] 1. This table is applicable to cast iron or steel housings. 2. If only central axial load is applied to the bearing, select such tolerance range class as to provide clearance in the radial direction for outer ring.

[Notes]1) Light, normal, and heavy loads refer to those with dynamic equivalent radial loads (Pr) of 5 % or lower, over 5 % up to 10 % inclusive, and over 10 % respectively in relation to the basic dynamic radial load rating (Cr) of the bearing concerned.

[Notes] 1) Loads are classified as stated in Note 1) to Table 9-4 (1). 2) Indicating distinction between applications of non-separable bearings permitting and not permitting axial displacement of the outer rings.

– Arctic Cat      Most ATV / UTV inc. Wildcat and Prowler – Can-AM      Most Maverick, Outlander, Commander, Renegade, & Traxter – CF Moto* – Honda * – Kawasaki     Most Brute Force, Prairie, Mule, Teryx, etc – Polaris      Most RZR, Ranger, Sportsman (inc. XP series), & Scrambler – Suzuki* – Yamaha      Most Grizzly, Wolverine, Big Bear*, Kodiak*

Depending on your machine make and model, one (1) or two (2) Tool Greasers may be required.  The prices are $50 for one (1) unit or $90 for two (2) units, which includes shipping within the continental US; except Alaska and Hawaii),

“I have a 2013 Polaris Sportsman 550 Touring with very low miles.  I saw the Machine Intergrations product on U Tube and thought it was interesting.  Purchased the MI-BGP-1628 which was for my model.  I opted to remove the front bearing housing as it made it easier to grease.  A bit more work but worth it.  All four bearings took over twenty shots of grease.  Spin the bearings and another four shots of grease.  Not a doubt that this was highly beneficial as well as VERY easy to do.  A great product at a great price. ” –  Doc M. (via email)

Ballbearing tolerance table

Bearing tolerance tablepdf

[Notes] 1) Symbols T and L means interference and clearance respectively. 2) In the columns "single plane mean outside diameter deviation" and "fit" upper row values are applied in the case of D≦18mm, lower row values in the case of 18 < ＜D≦30mm.

Depending on your machine make and model, one (1) or two (2) Tool Greasers may be required.  The prices are $50 for one (1) unit or $90 for two (2) units, which includes shipping within the continental US; except Alaska and Hawaii),

Wheel bearings for ATV’S and UTV’S do not come with enough bearing grease to sustain the use that you need, to keep riding without fail.  Limited grease leaves voids for water and dirt to enter and remain in the bearings.  Don’t let this happen to your investment!

Wheel bearings for ATV’S and UTV’S do not come with enough bearing grease to sustain the use that you need, to keep riding without fail.  Limited grease leaves voids for water and dirt to enter and remain in the bearings.  Don’t let this happen to your investment!