Oil Seal Size chartin inches

Whether you need to prevent leaks, remove contaminants, control pressure, or reduce friction, auto oil seal ​manufacturer HONGLEI's mission is to help you find the right sealing solution for your specific application requirements and business needs.

All are fitted with a spring to preload the sealing lip. All these types are for non-pressurised or low-pressure applications up to 0.5 bar for diameters of a limited size. For diameter of 500 mm or more, the maximum pressure is 0.1 bar. For higher pressures, special types or PTFE lip seals can be used.

These cassette seals are widely used in wheel-end applications, such as the axles of agricultural machinery or off-road trucks.

The lip is specially designed to ensure the oil seal works effectively with the different forces that arise during rotation. Many different designs and materials are used, so countless types of oil seals are available. These are chosen according to the application; pumps, gearboxes, wheels, and many other rotating applications where fluids need to be sealed. They are used in a variety of sectors, such as the chemical industry, manufacturing, wind turbines, automotive sector, food industry, and more. Oil seals are used in nearly all sectors.

Oil seals are found in a wide range of applications, in virtually every industrial sector. It is essential to select the correct oil seal so that the application in which it is used can run efficiently, free of leaks or other issues. In this blog, we explain which factors you should pay attention to when selecting the best oil seal for your application.

These types are made with a metal outer case and a PTFE lip. They are suitable for a wide range of temperatures from -90 °C to +260 °C.These lip seals can also be used for higher pressures of up to 10 bar (special types up to 25 bar) and rotational speeds of up to 40-45 m/s. Certain grades of PTFE are suitable for use in pharmaceutical and food applications. One important point is that PTFE lip seals do require a shaft with a harder, smoother finish.

Deep Groove Ball Bearing Size Chart ; 6000, 10, 26 ; 6001, 12, 28 ; 6002, 15, 32 ; 6003, 17, 35 ...

Replacing a critical component can be difficult to get right, especially if you do not have the original machine specifications. Thankfully, there are a few ways to identify oil seals; from their design, size and material. As there are hundreds of different oil seals available on the market, this guide will cover the four most common design types. Typically available with either a single or double lip, in Nitrile or Viton Rubber Material.

Spring seals and O-rings are very different products, but they ultimately accomplish the same goal of a sealing system. In short, the unassuming O-ring is a rubber ring. A spring seal consists of an engineered plastic sheath and a metal spring element. While both are seals, they have limited commonalities in design, intent and function.

Oil seal size chartpdf

Before fitting the oil seal, it is essential to check that the oil seal, shaft and bore are clean and undamaged. The surfaces the oil seal will come into contact with must be free of sharp points or burrs. The sealing lip is fragile, so even minimal damage can cause a leak. It is also important that the shaft and bore are correctly finished.

The same design as type A with corrosion protected metal case and stainless-steel garter spring. Suitable for use with a wide range of fuels and chemicals.

The sealing lip is always made of a rubber or synthetic material. For oil seals with a rubber outer case (R, RST, GR, GRST), the rubber quality of the sealing lip and the outer case are the same.

Standard springs are made of carbon steel. We use stainless-steel springs for our GR and GRST oil seals made from FKM rubber. In some rare cases, an O-ring is even used as a spring element. Standard PTFE lip seals are not fitted with springs.

Oil seals are available in an immense range of sizes, for shafts from a few millimetres to several metres. Once the shaft diameter, groove diameter (housing diameter) and groove width are known, selecting an appropriate oil seal is a simple task. An oil seal or its product description is usually associated with three dimensions, for example 6x15x4. These refer to the sizes of the hardware for which the oil seal is designed. In this example, this oil seal is suitable for: 6-mm shaft diameter x 15-mm groove diameter x 4-mm minimum groove width.

Home SKF Brands Locations Certifications Affiliates Jobs Search Login Register Forgot password Terms & conditions Privacy policy Site ownership Cookies General conditions of sales

ERIKS also supplies the types GR and GRST. These are virtually identical to the types R and RST, except in this case the metal inner ring is also completely encased in rubber. ERIKS uses FKM rubber here as standard, so these seals are ideal for use in acidic environments.

SKFOil seal size chartpdf

2024923 — 2011 Chevrolet Malibu LT has been making a loud humming that has just gotten louder each day. Fast forward to current day, and while driving back home, the car ...

project288-PHRE Uganda. Promotion of Hybrid Renewable Energy Systems Towards Electricity Access in Uganda | PHRE. women ...

FKM or FPM, which is in well-known brand Viton™, can withstand higher liquid temperatures of up to 180 ˚C. FKM is highly resistant to strong acids and bases, as well as to synthetic oils and greases. Glycol-based oil and grease, however, can also damage FKM.

VMQ, also known as silicone, is also used for oil seals, but this is less common because the mechanical strength of VMQ is low and this material has poor wear-resistance This makes it less suitable for dynamic applications, but it can withstand fairly low and high temperatures from -60 °C to 200 °C. Many types of VMQ are also suitable for contact with pharmaceutical and food products, so VMQ is an option worth considering. VMQ oil seals are usually available on request.

Fully covered outer diameter for excellent sealing. This oil seal is fully enclosed in a rubber material and is the most widely used type of oil seal. Great resistance to thermal cycling, temperatures and different chemical resistance.

The group of oil seals used in dynamic applications include radial shaft seals that seal a rotating shaft around its circumference. They are also known as lip seals, but in this blog we will use the term oil seals.

Always start by making sure the oil seal is facing the right direction. The oil seal must be positioned with its spring to the side of the medium to be sealed. The oil seal must then be pressed into the bore. It must fit tightly (H8 in the groove is recommended). Use appropriate tools for this, such as an impact socket set, to ensure that the force is applied evenly during pressing. The oil seal must never be hammered into the bore with brute force, but eased in.

SPHERICAL ROLLER BRG TAPERED BRASS C3 CLEARANCE 160X340X114MM ROLLWAY. 22332 MBKW33C3 R. Brand: Rollway. Your order will be fulfilled from your branch.

Home  >  News  >  Resources  >  Oil Seal Size Chart

Kaydon is ready to meet your bearings needs around the world, with sales offices on three continents. Contact us today to find out how Kaydon's engineering experience and expertise can help you solve your most demanding ball bearing and slewing ring bearing challenges.

The metal used in the outer case of oil seals is usually made of carbon steel. Upon request, and depending on quantities, a different type of steel (such as stainless steel) can be used.

Industry retailers use unique codes to identify oil seals worldwide. The most common lip style designations are 21 (single lip) and 23 (double lip), please read our Oil Seal Cross Reference Guide for more detailed information.

With the rapid development of social economy, the market competition has become more and more fierce. Therefore how to control the cost is the key to improve the competitiveness and adapt to the economic development. China is one of the first places to consider when looking for low cost oil seal inventory for your store.

MetricOil Seal size chart

Leather  Recommended for abrasive applications  Good running properties, due to the impregnated seal lip  Can be used on shafts which have a surface roughness outside the range for rubber seals  Not suitable for water

Firstly, the oil seals covered in this guide classify the single lip as the inner diameter at the bottom of the component. The single lip is vital to the function of the seal by containing the oil, grease or lubricant. The only difference between a single and double lip is the additional rubber lip on the top of the oil seal which helps prevent dust or dirt from coming close to the shaft. Identifying the oil seal lip can be misinterpreted with a visual inspection alone. For or this reason, you should press along the inner diameter at the top of the seal, if you feel a ridge with a slight movement or give it is highly likely you have a double lipped oil seal.

The most common oil seals are the ERIKS types R, RST, M and MST, which correspond respectively to types A, AS, B and BS according to DIN 3760/ISO 6194.

ERIKS type R (type A according to the DIN standard) is identical in shape to type M, but has a rubber outer case with metal reinforcement on the inside. The rubber creates a good seal in the housing, even if the housing has suffered minor damage or is not in its best condition for other reasons. The RST version has a dust lip. These types are often chosen to replace a type with a metal outer case because they are easier to install and can cope with minor damage to the groove, such as scratches.

ERIKS type M (type B according to the DIN standard) has a single metal casing and rubber sealing lip. Since the casing is made of metal, it must be fitted in a well-finished, undamaged groove. Large volumes of oil seals with metal casings are often cheaper, which is why they are often used as original equipment in machines. However, if an oil seal has to be replaced, types with a rubber exterior (type R or RST) are easier to fit. Type MST is similar to M and commonly used. The difference is the dust lip in the MST oil seal that prevents dust and dirt reaching the sealing lip, and extends its service life in dusty environments.

Nitrile or NBR is black in colour, whereas, Viton or FKM is usually a brownish colour. To understand the main comparisons between the two compounds read our Nitrile vs. Viton article.

Log in to access Slewing Bearing 3D models & CAD files. Access Thin Section Bearings at SKF.com  Forgot password?  |  Register

On average, a wheel bearing costs you $50 to $200. Besides the cost of the parts, ‌replacing the front or rear wheel hub assembly is labor-intensive and ...

Rubberoil seal size chart

Economic metal outer diameter for standard applications. This is an economical oil seal where the metal is exposed on one side and offers a closer fitting between the oil seal and housing or bore. Due to this, it has limited use with sealing thin liquids or gases.

Usually, these oil seals are used to seal lubricating oil or grease and contain it within the application, so that moving parts such as bearings are continually supplied with enough lubrication. However, such seals are also used for sealing other liquids, gases, and solids, such as powders or granules.

The quality of the rubber or rubber fabric used to make an outer case is the same as the quality of the rubber sealing lip. Fabric reinforced rubber is, as the name suggests, rubber reinforced with a fabric.

Finally, Polymax part codes follow the same pattern as our O-rings - inner diameter, outer diameter and height. This is different from the industry-standard convention, whereby imperial oil seals follow - outer diameter, inner diameter and height.

Oil/fluid leaks are considered to be the most typical problem that vehicle owners typically deal with. If you check for stains, puddles or blemishes under your vehicle, don't ignore it and ask your local mechanic to check and fix the problem as soon as possible. If the engine is leaking oil, you need to address the problem immediately as it will oil the engine components.

HONGLEI is a leading enterprise in China, our products have passed the testing of Hebei Province Rubber Products Inspection Center. Our main product lines include: automotive oil seals, agricultural oil seals, tractor hub oil seals, valve stem seals, precision rubber parts, O-rings. We also accept customers' own design and OEM design orders, always focusing on quality products.

Dec 15, 2022 — A failing wheel bearing will increase your difficulty in driving. But with a high-quality wheel bearing, you can drive for another 1000 miles as per the ...

NationalOil Seal Size chart

Copyright © Xingtai Honglei Seal Manufacturing Co., Ltd. All Rights Reserved. | Sitemap | Sitemap

Most standard oil seals have to comply with the DIN 3760 and ISO 6194 standards. Different standard types of oil seals are available that comply with these requirements.

Oil seal sizecalculator

EPDM oil seals are less common. They are used in solvent, hot water and steam applications, EPDM resists low temperatures down to -50 °C and UV radiation well. Some types of EPDM are also suitable for higher temperatures up to +150 °C. EPDM oil seals are usually available upon request.

​Hydraulic seals are typically made from elastomers, natural and synthetic polymers that have weak molecular attraction and high elastic properties. The two primary sources of hydraulic seals are rubber and plastics (including PTFE, such as Teflon and polyurethane). Other elastomeric materials used to make seals include butadiene, nitrile, butyl and silicone resins.

The sealing lip of the RST-D is more heavy-duty, so it can cope with pressures of up to 10 bar at slightly lower rotation speeds.

The same design as type B with an additional inner case for greater structural rigidity. This type of oil seal is typically used in heavy-duty engineering machinery or large diameter sized seals

Cassette seals are designed to maximise grease or oil retention and protection against liquid or solid contaminants. These seals are provided with their own bushings in which dirt is kept out and oil/grease kept in by a multi-lip seal.

Polytetrafluoroethylene  Chemical resistant  Low coefficient of friction poor elastic properties not wear resistant if used by dynamic applications

SKFOil Seal size chart

Polyacrylate  Better heat, oil and chemical resistance than NBR  It is recommended for use in oil which contains load bearing additives such as EP gear oils

Have you found the right oil seal for your application? The next step is fitting the oil seal correctly, so that it remains undamaged.

To install an oil seal properly, the shaft must be undamaged. This is so the oil seal can do its job properly on the one hand, and to prevent it from being damaged during fitting on the other. In addition, it is very important to lubricate the shaft, the sealing lip and the bore with plenty of grease. This will allow the oil seal to slide more easily over the shaft and prevent dry running after the first rotation. The oil seal may also come into contact with the keyway, thread or other grooves when sliding over the shaft. By taping or covering the shaft at the location of these irregularities with oil-soaked paper, the oil seal can be mounted without damage to the sealing lip.

What should you take into account when selecting an oil seal? Different types of oil seals and various types of materials are available, each designed for specific uses. It is also important to select the right size of oil seal for the best results. For this reason, selecting the right oil seal requires adequate understanding of the application in which it will be used.

Other important factors are ensuring the hardness and roughness of the shaft are correct. A shaft hardness of HRC 45 is recommended for a rubber sealing lip, with a roughness of Ra 0.4-0.8. A higher shaft hardness of HRC 60 and shaft roughness of Ra 0.1-0.4 is recommended for a PTFE lip.

The material of the sealing lip is chosen according to the liquid to be sealed and the rotational speed. For larger shafts, an NBR sealing lip can cope with surface speeds of up to 10-12 m/s, while an FKM lip is suitable for speeds of up to 35-38 m/s.

ERIKS type GV (type C according to DIN) is equivalent to type M, but is a heavy-duty version with a double metal casing. This can be a useful solution with larger diameters in more demanding applications. There is also a version of this type with a dust lip; the GVST (type CS according to DIN).

PTFE, which is used in the well-known brand Teflon®, is less commonly used, but it is the preferred material for specific rotating seals in the chemical, food and pharmaceutical industries. This material is notable for having a very low frictional resistance and the best chemical resistance. It can also withstand a very wide range of temperatures in these types of seals; -80 ˚C to 200 ˚C. The shafts on which oil seals with PTFE lips are used require a harder and finer finish. Something like an axle sleeve can also be used to meet this requirement.

Global O-Ring and Seal’s Oil Seal Size Chart contains over 15,000 size combinations of oil seals. Shaft, Bore, and Width are all searchable in inches and millimeters. This interactive chart will display all matching sizes based on the dimensions keyed. For more information or to request a quote, please call 832-448-5550 or submit the Product Inquiry Form on the Oil Seals Page or Fabric Reinforced Seals Page. Conversely, these oil seal dimensions can be searched within our online store by clicking on either of the buttons below.

George Lodge & Sons Ltd has been a distributor of bearing products since the 1920's when it became an authorised distributor for the Ransome & Marles ...

NBR, also known as nitrile rubber or nitrile, is the most popular material for an oil seal because of its good resistance to many oils and greases, such as mineral grease and hydraulic oil. Depending on their composition, synthetic oils and greases, such as those based on glycol, can damage NBR rubber materials. Depending on the amount of glycol, a PTFE lip seal may be the best choice. NBR is also unable to cope with contact with acids and solvents. The rubber is suitable for oil and grease at temperatures from -35 °C to 100 °C.

We hope the information in this article helps you identify the correct oil seal for your application. If you have any queries feel free to call one of our sales engineers on 01420 482862. Polymax stock over 6,000 oil seals available to buy online, browse our oil seal selection today.

Ball bearings are used in many machines with rotating motion, from fans and car engines to large medical precision equipment, ensuring smooth and efficient.

Because of the higher temperature resistance of FKM, this material is also chosen for applications where higher speeds play a role, which raise the temperature at the sealing lip considerably. Usually, using FKM will result in a longer life than using NBR. This compensates the higher price of FKM compared to NBR, as an FKM does not have to be replaced as frequently. The low temperature resistance of standard FKM is limited to -15 ˚C.

Silicone  Wide temperature range  Commonly used in low temperature applications  Very prone to mechanical damage during fitting

The average cost for a Wheel Bearing Replacement is between $283 and $377. Labor costs are estimated between $162 and $204 while parts are priced between $121 ...

Nov 5, 2014 — Which of the following includes the two conditions necessary for the equation, v^2 = u^2 +2as, to apply? I know the answer is a has constant ...

Keywords: oil seal manufacturers in china symptoms of bad valve seals oil seal for sale Oil Seal Size KDIK Oil Seals Kubota Front Drive Shaft Seal Replacement Power Steering Oil Seal Sitemap Tags

These are comparable to type R and RST, except the outer case does not have a metal reinforcement ring. To compensate, the outside is not made of normal rubber, but a hard, heavy-duty rubber fabric. The advantage is that these types can be made in a split version. They are almost always produced to order, and made of NBR or FKM.