Copyright © 2024 · WTWH Media LLC and its licensors. All rights reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.

There are different kinds of wheel bearings depending on the year model and the design of the vehicle. Older rear wheel drive vehicles had cone type wheel bearings on the front wheels that could be removed, inspected, and packed with grease, and reinstalled with new seals. Some front-wheel drive vehicles have wheel bearings of this type on the rear. In other words, if a vehicle has cone-type bearings that can be removed, inspected, and repacked, it will always be on the NON-driving wheels – the ones that don’t propel the vehicle. Trailer wheels often have bearings of this type.

Since the wheel bearings keep the wheel and hub assembly spinning on an axis, if the wheel bearing is compromised to the point that it can no longer maintain that axis, driving with a faulty bearing can be extremely dangerous—especially at high speeds. Think about a wheel that starts wobbling because the bearing decided to completely come apart while you’re in freeway traffic. This can happen without warning if you’ve become accustomed to the bearing’s noise as it continues to warn you by getting louder.

Where accuracy is required, it is important for engineers to consider the forces acting on a bearing. Because a bearing typically supports the free motion of a shaft about an axis of rotation, two forces normally act on the bearing: a radial load and a thrust load. But, what is the impact of these forces? Here, Chris Johnson, managing director of miniature bearings expert SMB Bearings, explains.

Radialload bearing types

Wheel bearing failure is a potentially dangerous situation at any time, so have your vehicle towed to the nearest mechanic and have your faulty wheel bearings replaced right away. Vehicle safety should always come first.

When you’re driving with the music cranked up, you may not notice the different sounds that your vehicle makes. But the moment you turn the radio off and notice a growling, humming, or rumbling noise coming from your wheel bearing, you’ll know there’s a problem.

Can your car still run with a faulty bearing? The technical answer might be yes; some wheel bearings might continue to operate normally despite the vehicle being driven with one or more noisy bearings for a very long time. The problem is that since the noise begins gradually and slowly gets worse, you might not even notice the noise if your vehicle is noisy in other ways.

You might have seen a vehicle pulling trailer that has had the bearings neglected to the point that the wheel gets hot enough to set the tire on fire – it can happen on your vehicle in extreme cases, but it’s rare.

Radialload example

Loose wheel bearings can throw your car’s alignment off, leading to abnormal tire wear. There are, of course, many other problems that can create the same, undesirable results.  So, you’ll want to diagnose the issue thoroughly before condemning one or more of the wheel bearings

Richard McCuistian has worked for nearly 50 years in the automotive field as a professional technician, an instructor, and a freelance automotive writer for Motor Age, ACtion magazine, Power Stroke Registry, and others. Richard is ASE certified for more than 30 years in 10 categories, including L1 Advanced Engine Performance and Light Vehicle Diesel.

It’s this abnormal sound that’s the most obvious sign something is wrong with your wheel bearings. Of course, because other issues, such as cupped tires, can mimic a bad wheel bearing, you’ll want to diagnose the sound properly.

Wheel bearings support the weight of the vehicle and allow the wheel/tire assembly to rotate when you’re traveling down the road. All four of your car’s wheels have wheel bearings and they are designed to last the life of the vehicle. In fact, many vehicles will travel hundreds of thousands of miles/kilometers and never need a wheel bearing replacement, but others may need one or more wheel bearings replaced over their lifetime.

Apart from the signs that can make us aware of a worn-out car wheel bearing (grinding noise, car looseness, heat on the wheel, and steering wheel pulling),

Choosing the right bearing There are a variety of measures that manufacturers can take to ensure long bearing life. The first step is to limit the radial load to between 6–12% of a bearing’s dynamic load rating. Although a bearing is able to tolerate a much higher load, its life will be shortened.

By choosing the right type of bearing and considering key factors in the battle to control radial and thrust loads, engineers can ensure they continue to innovate while delivering the highest levels of accuracy, smoothness, and bearing life.

A radial load acts perpendicular, at 90°, to the axis of rotation, while a thrust load — also known as an axial load — acts in parallel to the axis of rotation. Any misalignment of the shaft can also result in a moment load, a tilting force that can increase wear.

Another tricky element of wheel bearing noise is the need to pinpoint which wheel bearing is making the noise. Sometimes even professional mechanics will struggle with this, and there are special listening devices shops use to pinpoint which bearing is making the noise. Some tire shops will replace both front bearings if there is a bearing noise coming from the front of the vehicle; not a bad practice, actually.

I have personally seen a Crown Victoria that was making a noise I would have sworn was coming from the left rear axle bearing, but after removing and inspecting that bearing (which is difficult on a rear wheel drive vehicle), I discovered that the noise was actually originating from the left front tire. And I had nearly 40 years of automotive experience at the time.

Pro Tip: If a noise happens after the tires are rotated on a front wheel drive vehicle, it may be due to the wear pattern on the tires, so be aware of that, too.

Some may say that you can drive for up to a thousand miles with a failed wheel bearing—but the thing is, this is an arbitrary claim. There’s really no telling how long you can safely drive your vehicle in this state. It would depend on the severity of the damage to your wheel bearing, present road conditions, and other factors. So, it’s best not to push your luck.

Radialand axial load on bearing

By now, you may have an idea of how important wheel bearings are. Thankfully, there are signs that can indicate that your wheel bearings are going bad.

Pro Tips are nuggets of information direct from ASE-certified automobile technicians working with CarParts.com, which may include unique, personal insights based on their years of experience working in the automotive industry. These can help you make more informed decisions about your car.

Remember, the wheel bearing not only allows the wheel/tire assembly to rotate along with the hub the wheel is bolted to, the bearing also carries the weight of the vehicle and maintains the spinning wheel’s axis by keeping it in a straight line. A failed wheel bearing won’t usually allow the wheel to come off completely unless the bearing has become so hot that the axle or spindle is glowing red. Not only can this cause a fire in the wheel well area, the wheel and hub can separate from the vehicle and… well, finish the thought. Granted, this is a very extreme case of a wheel bearing failure, but wheel bearings that have lost their grease can get extremely hot.

Timken LM104911-2T Tapered Roller Bearing Single Cup | Imperial | 82.6 mm 3.3 in OD | 16.5 mm 0.7 in Width · Attributes · Features ...

Any information provided on this Website is for informational purposes only and is not intended to replace consultation with a professional mechanic. The accuracy and timeliness of the information may change from the time of publication. Read our full disclaimer here.

Axial load bearing

This paragraph doesn’t make sense: Older rear wheel drive vehicles had cone type wheel bearings on the front wheels that could be removed, inspected, and packed with grease, and reinstalled with new seals. Some rear wheel drive vehicles have wheel bearings of this type on the rear. In other words, if a vehicle has cone-type bearings that can be removed, inspected, and repacked, it will always be on the NON-driving wheels – the ones that don’t propel the vehicle.

Once again, there are other issues besides a bad wheel bearing that can cause steering wheel vibrations. A thorough diagnosis is needed to verify the cause of the concern.

A bad wheel bearing can cause the brake rotor to wobble, which shoves the caliper piston back into its bore so that when you apply the brakes, you have unexpected pedal travel as a result – making it harder to stop or causing the vehicle to pull unexpectedly to one side – never a good thing in traffic.

Modern vehicles have sealed wheel bearings that cannot be disassembled without destroying the wheel bearing assembly in the process, and on vehicles with bearings like those, you only know a bearing is bad when it begins to make noise. That’s the earliest indication of a bad wheel bearing, and front wheel bearings (both on front wheel drive as well as rear wheel drive vehicles) are the most prone to fail on modern vehicles.

The older style cone shaped bearings have a series of tapered rollers in a cage with a window for each roller to keep them evenly spaced while they ride between inner and outer races. But most modern sealed bearings have steel balls with inside and outside races.

Although a bearing may be able to tolerate a high static load, it will do so at the loss of accuracy and smoothness, making it impractical for use in high accuracy environments, such as electronics manufacturing and in robots used in food and beverage production. The typical static-load rating for a stainless steel bearing is approximately 75–80% of the load rating for chrome-steel bearings, due to the hardness of chrome steel.

In the event that this happens under weather conditions that make the road slippery, immediately maneuver your vehicle to the nearest safe spot off the road.

If the seal that is part of the bearing fails, moisture and dirt can enter the bearing’s grease, compromising the grease’s ability to keep the load bearing elements (balls and races) lubricated. But there are times when a bearing destroys itself even though the grease is not compromised. Tiny particles of metal can begin to flake off of the races, and when this happens, those particles mix with the grease so that it becomes a grinding compound of sorts, creating a “snowball” effect whereby more metal flakes off and enters the grease charge and the bearing gets noisier with time.

A worn-out wheel bearing may also make a high-pitched squealing sound while you’re driving. If you are able to observe these symptoms, have your vehicle checked right away. Even if your wheel bearings are not the culprit—there’s definitely something wrong with your vehicle.

Wheel bearing noise coincides with the rotation of the tires. The sound typically increases with vehicle speed as well. In some instances, the noise may also change when you turn the steering wheel in one direction or the other.

A faulty wheel hub and bearing assembly can also cause a vibration felt in the steering wheel. Often, the sensation will change with vehicle speed or while the vehicle is cornering.

Get quality wheel hub assembly replacement parts from 1A Auto & Get FREE shipping! Driving with a missing wheel bearing is dangerous. Even a bad bearing can ...

Design World Online The Robot Report Coupling Tips Motion Control Tips Linear Motion Tips Fastener Engineering Wire and Cable Tips

Oct 7, 2023 — This is a common problem after replacing the water pump, and it can cause overheating and steam leaks. To bleed the air out of the system, you can try the ...

Although thin-section bearings — where the difference between the inner and outer diameter of the bearing is small — are great for compactness and saving weight, they can only support axial loads of between 10 and 30% of the bearing’s static radial load rating due to the shallower raceways. Additional radial loads or moment loads will reduce thrust load capacity even further. Excessive thrust loads on a thin-section bearing can cause the balls to ride dangerously close to the top of the raceway.

However if the joint materials have coefficients of thermal expansion ... For important bolting applications it is recommended that the bolt preload is is ...

The greater the load, the higher the level of stresses the balls and raceways will be subjected to. This will lead to more rapid wear and a shorter bearing life. Fatigue failure results in the ball path being eroded, leading to spalling, where a fracture on the surface of the raceway causes material to be removed, ultimately leading to failure.

Radialload formula

Mechanics will find a safe, empty, smooth paved road, then listen carefully to the noise while swerving gently from side to side – typically when you swerve to the right, you’re increasing the load on the left side bearings, and vice versa. And again, while this is a good practice, it’s easy to be fooled into replacing the wrong bearing, even using this method – that’s why some tire shops replace bearings in pairs. If you use this method and believe the noise is tire related, you can move the front tires to the rear and see if the noise changes.

If your wheel bearing goes out while you’re on the road, it’s not advisable to keep driving. However, if there’s absolutely no alternative, make sure to maintain a slow and steady pace—do not accelerate or turn suddenly.

Applying a thrust load to a bearing can be beneficial. For example, applying a permanent thrust load (preload) to the inner or outer ring, using washers or springs, can eliminate play in the bearing and provide more accurate rotation. Conversely, applying an excessive load can be catastrophic. If engineers fail to adequately match a bearing to the radial and thrust loads in an application, it can drastically reduce the life of the bearing.

Thank for pointing out that typo. The paragraph was supposed to read: Some front-wheel drive vehicles have wheel bearings of this type on the rear. We have updated the article.

Axial load formula

Radialload vs axial load

Excessive loading can also lead to other signs of fatigue such as overheating, degradation of the lubricant and abrasion caused by flakes of particulate matter.

The wheel bearing on a wheel usually consists of a pair bearing assemblies running side by side on the shaft or spindle – this keeps the spindle running straight, while a single row of balls or rollers might allow the wheel to wobble. Exceptions would be the non-tapered roller bearings on rear wheel drive vehicles, which will have only one bearing assembly at the wheel end of the axle, but the inboard end of the axle on those units is splined to the differential assembly, which is spinning in its own set of tapered roller bearings.

Note by Richard McCuistian, ASE-certified mechanic: I have personally seen a Crown Victoria that was making a noise I would have sworn was coming from the left rear axle bearing, but after removing and inspecting that bearing (which is difficult on a rear wheel drive vehicle), I discovered that the noise was actually originating from the left front tire. And I had nearly 40 years of automotive experience at the time.

A typical radial ball bearing, which is designed primarily for radial loads, has a maximum static and dynamic load capacity. The static load capacity is the maximum radial load that a bearing can withstand before the load causes a total, permanent deformation of the bearing balls or the raceway equal to one ten thousandth of the ball’s diameter.

Also, by replacing a bad bearing early on, you can also save yourself a lot of money by avoiding possible major repairs.

It’s worth noting that tire noise will usually change depending on the road surface. Wheel bearing noise, on the other hand, is consistent regardless of road surface and acceleration.

Wheel bearings are in a hostile environment and are working very hard, but wheel bearings are very tough – they’re designed for the work they do. But product variability is a real thing, and again, some bearings fail while others never do.

Is your ABS light on, and you do not know what is causing it? A faulty wheel bearing can be a possibility. On some vehicles, the ABS sensor or encoder ring is integrated into the wheel hub and bearing assembly. As such, a failure of the wheel bearing can trigger the ABS light.

In cases like that, or when you just decide to keep driving until the failure is complete, the bearing itself will decide for you when it must be changed, and it can do so in very unpleasant ways and never at a good time. In other words, there are instances, when left unattended to, a faulty wheel bearing can create hazardous conditions, such as the following:

When calculating bearing life, it is important to consider load ratings, these are a measure of how quickly the rotating elements of a bearing will experience fatigue and the total number of revolutions a bearing can withstand before it fails. These ratings can be categorized into static load ratings and dynamic load ratings.

Jun 9, 2023 — Plaintiff Jason Fyk asserts that Facebook 1 improperly restricted and removed his Pages from the social network. And so he brings a claim against the United ...

This API enables you to search for cross-reference from a non-SKF designation (product number) to an SKF designation.

The CarParts.com Research Team is composed of experienced automotive and tech writers working with (ASE)-certified automobile technicians and automotive journalists to bring up-to-date, helpful information to car owners in the US. Guided by CarParts.com's thorough editorial process, our team strives to produce guides and resources DIYers and casual car owners can trust.

One tricky thing about wheel bearing noise is that a bad tire can make almost exactly the same noise as a bad bearing; you don’t want to replace a wheel bearing for a noise concern when all you need is a new tire.

Wheel End Bearings · Repair Kits · Support · Light ... pothole, or damage to your rims due to a large or deep pothole. ... wheel when you hit the hard edge of the ...

Radialload bearing

Ball Bearings Shield and Seal Types (Cat. No. 3015/E) Copyright NTN Corporation All rights reserved.

A faulty wheel bearing can cause your vehicle to pull to one side during braking. This symptom can also be related to faulty brake components.

The dynamic load rating, on the other hand, is the ability of 90% of a group of identical chrome-steel bearings, with only the inner ring rotating, to endure a radial load of a constant magnitude and size for one million revolutions before the first signs of fatigue develop.

The next step is to choose the right material. In SMB Bearings’ experience as a specialist in thin-section, corrosion-resistant, and miniature bearings, choosing the right type of bearing can also make all the difference. While all radial ball bearings have some thrust load capacity, it’s often better to use heavy-duty bearings that have deep raceways if greater thrust loads are present as these can withstand axial loads of up to 50% of the static radial load rating.

Dec 3, 2023 — NK2215 Flight Status LIVE: SPIRIT Flight NK 2215 from Cancún, Cancun to New Philadelphia in real-time. NKS2215 arrival, departure, delays, ...