Both the hub assembly and wheel bearings allow the wheels to rotate freely. Although they are designed differently, the function and application are similar. The wheel hub assembly has a hub bearing that is housed inside the assembly and cannot be taken apart for repair. Hub bearings are a part of the hub assembly and are pre-packed by the manufacturer to be sold as a complete unit. Whereas the wheel bearings are repairable and can be removed or replaced for lubrication. Wheel bearings are mostly used in vehicles with drum brakes. However, drum brakes are less used on vehicles (only at the rear brake) and the hub assembly is used on cars today with the increasing use of disc brakes. Wheel hub assemblies also feature studs that allow the brake rotors to attach to them.

The wheel hub assembly replacement cost depends on various factors, such as the price of the component, vehicle’s make and model, labor charges, etc. Some factors that contribute to the total replacement cost are mentioned below.

2013Honda Civicwheelbearing replacement cost

In this article, we’ll explore the key differences between a timing belt vs timing chain. We’ll also cover signs of bad timing components, the replacement cost of a broken timing chain or belt, and other aspects concerning timing belt or chain replacements.

2012Honda Civicwheelbearing replacement

You can also find out if you have a timing chain or belt by checking the engine. If it has an unsealed plastic cover on the front, you have a timing belt since the rubber belt runs dry.

Work in reverse order the way you removed everything. Install the hub assembly by bolting the hub to the steering knuckle.Use a torque wrench to tighten the bolts to the specs mentioned in the service manual.Connect the ABS sensor with the connector.Install the brake rotor back onto the hub and install the brake brackets back to the knuckle. Replace your brake rotors if they show signs of warping or damage.Tighten the bolts and install the brake calipers and brake pads back onto the bracket.Reinstall the axle nut and tighten it to the recommended torque specs. It’s recommended to replace your old axle nut and hub cap too if it’s broken or worn out. Replace the cotter pin to ensure safety.Reinstall the wheel and hand tighten the nuts before lowering the vehicle.Lower the vehicle and tighten the lug nuts to proper specifications.Perform a last check by driving the vehicle around to make sure everything is in its place.The only difference between replacing a front and rear hub assembly is that the rear wheels have the parking brakes, i.e. the drum brakes and the brake shoes, which you have to remove first in order to remove the hub assembly. However, some vehicles also have rear disc brakes other than the parking brakes and they have to be uninstalled in a similar way you remove the front disc brakes.

Front wheelbearing replacement cost

The cost of rear hub assembly varies between $80 to $200, depending on the type, make, and model. The cost of replacement charged by workshops‌ varies between $100 to $150. While the hub bearing alone costs somewhere between $50 to $80, the cost of the sensors varies between $30 to $50. That makes the overall replacement cost vary from around $180 to $350.

You also have to get the wheel alignment done after the replacement if you have removed the ball joint from the knuckle in order to separate the axle shaft from the hub. This also increases the cost of replacement by $100 to $150. You can reduce this cost by doing the alignment yourself, for which you can refer to the DIY wheel alignment guide. However, in most vehicles, the wheel alignment is unnecessary after replacing the hub assembly.

A hub bearing, also known as a wheel bearing, is a component of a vehicle’s wheel assembly that supports the wheel and allows it to rotate smoothly. Hub bearings are typically made up of an outer ring, an inner ring, and a set of balls or rollers that allow the wheel to rotate. They are designed to withstand the weight of the vehicle and the forces generated during driving, such as cornering and braking. Hub bearings are an important part of a vehicle’s suspension system, and they play a crucial role in ensuring a smooth and safe ride.

These materials also enable differences in how they run. For example, a light rubber belt is quieter than a heavy metal chain. However, recent improvements have reduced timing chain noises close to those of a rubber drive belt.

The hub assembly is a key part that supports the vehicle and houses the precision bearings, seals, and sensors. In front-wheel-drive cars, the front hub assembly connects the CV axle shaft, which transmits power to the wheels. Usually, a hub assembly has ‌4 or 5 long extended studs to which the wheel is attached, and the lug nuts hold the wheel with the hub. The front wheel hub assembly is one of the key components of the steering system crucial for contributing to the safe steering and handling of the vehicle.

A hub in a car is a component that connects the wheel to the rest of the vehicle. It is located at the center of the wheel, between the brake drums and the drive axle. The hub has two primary functions: to drive the wheels and to swivel so that the car can be steered. In a front-wheel-drive car, the hub rotates in or next to a large casting called a hub carrier. The carrier itself is mounted to the suspension with ball joints that allow it to swivel and move up and down. The amount the hub carrier can swivel is controlled by the steering gear, to which it is attached by a steering arm with another joint. The hub and drive shaft rotate inside a cast hub carrier which is turned left or right to steer the car. The most common way of transmitting drive from the drive shaft to the hub is by splines grooves machined for a few inches along the end of the shaft which engage with matching grooves inside the hub.

Yes, you can replace a worn or broken timing belt or chain if you have the knowledge and tools to disassemble the cars engine. This can include removing a tensioner, idler pulley, water pump, and more, in addition to the broken timing chain or belt. It’s a labor-intensive process.

Honda CivicWheelBearingprice

Although the wheel hub assembly replacement cost mainly depends on the car make and model you drive, the price of a new front hub assembly varies between $100 to $400. The cost of replacing the wheel hub assembly can be reduced by replacing the faulty components instead of replacing the whole assembly. On average, a wheel bearing costs you $50 to $200. Besides the cost of the parts, ‌replacing the front or rear wheel hub assembly is labor-intensive and requires special tools and skills. The average labor cost of replacing your wheel hub assembly can vary between $120 to $180. Which makes the overall replacement cost approximately $220 to $580. Be careful while purchasing a new wheel hub assembly for your vehicle. Do not risk purchasing a cheap quality part and the expense of quality. Purchasing a good-quality wheel hub assembly is as important as selecting the correct wheel hub assembly for your vehicle. You can refer to our ultimate wheel hub assembly buying guide to ensure you choose the correct part, which can save you a lot of money in the long run.

The timing belt (cam belt) and timing chain perform the same function. They maintain the engine timing and connect the crankshaft (which controls the piston) to the camshaft (which controls the intake and exhaust valve timing.) But they aren’t completely the same.

A timing belt is usually located outside the engine, while a timing chain is located within the engine — where it receives lubrication from engine oil.

The cost of replacing a wheel can vary depending on the type of wheel and the car model. According to J.D. Power and Associates, the cost of changing tire rims can range from $200 to $500 per wheel or $800 to $2,000 for the entire car. The price depends on the vehicle and the car service, but the minimum cost of changing tire rims is around $200.

The OEM (Original Equipment Manufacturer) wheel hub assemblies cost more compared to aftermarket ones. Aftermarket parts are a better as they will help you save money on your wheel hub repair costs because they are cheap and are offered with the same specifications, fit and function as the OEM parts. Aftermarket parts offered by reputed brands also come with OEM equivalent warranties and they meet or exceed OEM performance. Some top-quality recommended aftermarket wheel hub assemblies are mentioned below.

Replacing a wheel hub assembly is almost similar for all vehicles. The complete process requires technical expertise and specific tools. If you have replaced the control arm or the brake rotors on your vehicle, you might be able to do this as well. Here is a stepwise guide on how to replace your wheel hub assembly and the tools required.

Our certified mobile mechanics come to your home or office to complete your repair. We make the process easy from start to finish by offering upfront pricing, online booking, after-hours support, and a full warranty.

Hondawheelbearing replacement cost

Like every other moving part, a hub assembly also wears out with time and it is mostly because of a bad or damaged wheel bearing. Although the bearing in the hub assembly has a long life of 100,000 to 150,000 kilometers, sometimes they get damaged because of a failed seal or a severe impact from potholes at high speeds. It is easy to identify the signs of a failing wheel hub assembly and some ‌of them are‌‌ mentioned below:

Please note that this is a general guide and the specific steps may vary depending on the make and model of your vehicle.

If you are looking to purchase new rims to replace old, worn-out wheels, you can expect to pay between $30 and $1000 per rim. However, if you only need to replace a damaged wheel, you may not need to replace all four wheels. According to Cars.com, many original-equipment aluminum wheels can cost hundreds of dollars to replace.

Honda Civicwheelbearingnoise

But remember, you’ll probably need a belt replacement more often than you’d possibly need a chain replacement. However, both chain and belt replacement costs are cheaper than the auto repair costs you’d incur when your timing chain or timing belt breaks.

Majority of the vehicles today use a complete hub bearing unit. The hub bearings are the major contributor to the total price of the unit and can cost somewhere around $80 – $300, depending on your vehicle. Other vehicles use pressed-on units which are more popular in German and Japanese cars. Although these are cheaper compared to the complete hub assembly units, the cost of replacing the bearings is comparatively more, because it involves the removal of the entire steering knuckle and the bearing has to be pressed out. This increases the labor charge, which can amount to ‌$200 – $400, including the cost of the part. In comparison between the two, a complete wheel hub assembly costs less and is a sensible decision while saving money on the total bill.

Wheel hub assemblies are crucial components that play an important role in steering and performance of your vehicle. If you own a car, crossover, or a truck long enough, chances are that you will ultimately have to replace your wheel bearings or wheel hub assemblies. Unlike tire rotations, engine oil changes, brake components replacement, routine maintenance, etc., most owners do not know about the cost of replacing a wheel hub assembly because this part is not replaced frequently. This article will help you differentiate between wheel bearings and wheel hub assemblies and also help you with the wheel hub assembly replacement cost. Read more to learn about the cost of replacing your wheel hub assembly, how it works and how you can replace the front wheel hub assembly on your vehicle.

You may even be able to buy a timing belt kit or timing chain kit to do the replacement. A good timing chain kit will have all the replacement gears and tensioners included.

Fortunately, if your concern is mechanical timing maintenance, you can rely on AutoNation Mobile Service — an accessible mobile auto repair solution.With AutoNation Mobile Service, you get:

Some sample costs of replacing wheel hub assemblies for some popular car models are mentioned in the table below. These prices are an estimate and are subject to change. They do not include taxes, diagnostics, and other charges.

A timing belt or timing chain keeps your vehicle running efficiently. But depending on which one you have, the probability of its failure and the maintenance required can change.

The time it takes to replace a front wheel bearing hub assembly can vary depending on the make and model of your vehicle, as well as the location and labor costs of the mechanic. The average time it takes to replace a wheel bearing is between 2 and 4 hours . However, the time can range from 1 to 5 hours.

One of the main differences between a timing belt and a chain is its material. Like a serpentine belt (and some drive belt types), a timing belt is made of reinforced rubber. But a timing chain is made of metal.

Lexus wheelbearing replacement cost

A car manufacturer typically designs a cars engine to support specific mechanical engine timing parts. So, you won’t be able to switch between the two due to their locations and covers.However, if you’re lucky, you’ll be able to find a timing chain conversion kit specific to your vehicles engine. If you do, you’ll be able to replace your timing belt with a timing chain.

Both a timing belt and chain are crucial components of your car’s internal combustion engine. So, they need to be maintained well. Otherwise, they could cause catastrophic damage.

Like the serpentine belt, a rubber timing belt can develop cracks over time. So, you may need a belt replacement between 55,000 miles (about 90,000 km) to 90,000 miles (about 150,000 km.) Plus, oil and coolant leaks can speed up its wear.You need to be careful about a worn belt. If the belt breaks in an interference engine, it can lead to irreparable engine damage. However, this engine damage is prevented or reduced in a non interference engine.On the other hand, metal timing chains can last as long as the vehicle does. However, on high-mileage cars, you may need to replace the timing chain between 200,000 miles (about 320,000 km) to 300,000 miles (about 480,000 km.)

That’s because a timing chain break or broken belt or chain in an interference engine can lead to several other costly repairs. So, it’s helpful to have your engine timing components checked when getting any engine service and have the replacements done as soon as possible.

Note: Don’t confuse your timing belt with a drive belt (like the serpentine belt). A drive belt transmits power from the crankshaft to engine accessories like your air conditioning and alternator.

Now that you know how these two timing components work, let’s look at signs that indicate when you may need a replacement.

The cost of replacing a wheel bearing can vary depending on the make and model of your vehicle, as well as the location and labor costs of the mechanic. According to Car Talk, the average cost of replacing a wheel bearing is between $300 and $500. However, the cost can range from $250 to $1,100. The cost of the part itself is usually between $100 and $300.

On the other hand, a rubber timing belt is more susceptible to wear and tear. Plus, a worn chain will make strange noises to indicate issues, while a rubber timing belt might snap without warning.

2014Honda Civicfront wheelbearing replacement

Alternatively, you have a timing chain if the engine block has a sealed metal cover (to prevent engine oil from leaking.)

Note: Your timing belt or timing chain should be in its best condition while running. This is important to ensure your safety on the road.

Similar to the front wheel hub assembly, your vehicle has a rear wheel assembly too that allows the rear wheels to rotate  freely. Unlike the front hub, rear-wheel hubs, on most cars, are ‌non-driven hubs except for vehicles with rear-wheel drive. Most modern-day cars come with a front-wheel-drive option which makes the rear hubs free from the axle shaft or torque shaft. This makes the replacement of the rear hub assembly much easier than the front ones. While the vehicles with the rear wheel drive option have a similar hub assembly to the front-wheel-drive vehicles, which makes it a little hard to replace them. Like the front hub assembly, the rear hub assembly also houses the wheel bearing, as well as ABS and traction control sensors.

Yes, it’s possible in extremely rare cases. But usually, replacing a mechanical timing belt with a timing chain or vice versa is an impossible task.

And while they each have their pros and cons, you’ll have to make the most of what you have — unless when purchasing new vehicles.

Another major factor which affects the cost of wheel hub assembly replacement is the make and model of your vehicle. For example, if you own a truck like a Dodge Ram 1500, the price of hub assembly can vary between $350 to $550. Whereas, the same part costs $180 to $270 for a Honda Civic.

So, it’s best to leave a broken timing belt or chain replacement to a certified mechanic. They’ll have the tools and knowledge to complete the job successfully.

And even though a professional replacement would cost more, it could help you save money in the long run. That’s because an improper repair could lead to a totaled engine, and the vehicles engine repair would cost more than just a belt or chain replacement.

Often there aren’t many obvious signs of bad mechanical timing components. However, you may notice some of these symptoms:

The wheel hub assembly is also responsible for the working of your vehicle’s Anti-lock Braking System (ABS) and the Traction Control System (TCS). It houses the speed sensor that constantly relays the speed to the vehicle’s ABS control module. The system uses this information to engage the ABS during hard braking and prevents the vehicle from skidding. The traction control system also uses this ABS sensor to operate and offer optimum traction while driving. A wheel hub assembly consists following components:

It is possible to replace a wheel bearing without replacing the hub, but it depends on the condition of the hub. If the hub is in good condition, it can be reused. However, if the hub is damaged or worn, it is recommended to replace it along with the wheel bearing. Replacing both the hub and the wheel bearing at the same time can save you money in the long run, as it will prevent future repairs and ensure that your vehicle is safe to drive.