12*35*11 bearing

These knuckles are professionally assembled by the Yota1 Team, allowing you to easily install new wheel bearings quickly, without requiring a press. You can drive with confidence knowing that the wheel-bearing was properly supported during installation and professionally assembled by the Yota1 Team.

6202bearing Dimensions

The final option is to have Yota1 weld on a Total Chaos Spindle Gusset. To install these gussets it is best to remove your wheel bearing before installation. This is why we have this option, we weld on the spindle gusset before any other components are installed to ensure nothing is damaged by the heat.

The 1st Gen Tacoma, 1st Gen Tundra, 1st Gen Sequoia, and 3rd 4Runner wheel bearings are a press fit in the steering knuckles. When installing new wheel bearings, the wheel bearing must be properly supported or it will destroy the bearing. This press job can be troublesome for even the best DIY mechanic, it requires building a jig and a proper press setup. On the video tab, you will find the wheel-bearing installation video by Timmy the Toolman, this can help you decide if you have the proper tools to replace a wheel bearing yourself. If you would like to complete this job with ease these Pre-Assembled Steering Knuckles are right for you.

WARNING: This product can expose you to chemicals, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

Larger Lower Ball Joint Knuckles for Later 1st Gen Tundra and Sequoias use 11mm bolts with 17mm heads, if still Genuine spec.

It is recommended to replace wheel bearings every 150,000-200,000 miles, if you are loaded heavy or off-roading often you may want to replace these every 75,000-100,000 miles. Wheel Bearing will start to make a rotational squeal or metal-on-metal sound when they have gone bad and should be replaced.

Yota1 Pre-Assembled Steering Knuckles have new KOYO wheel bearings, Genuine seals, new wheel studs, and remanufactured wheel hubs. The knuckles themselves are quality cores that are thoroughly inspected to ensure they are within Toyota specifications, with no cracks, bends, or flaws that would affect longevity. The optional dust covers are new Genuine dust covers and can be installed or pre-modified to allow them to be bolted on. Dust covers include new hardware. You can also choose to have a Genuine or 555 upper ball joint installed.

**THESE SPINDLES HAVE A 3-5 DAY DAY LEAD TIME. WHEN PURCHASING THESE SPINDLES, WE ARE CUSTOM BUILDING THEM FOR YOUR VEHICLE, ONCE THE ORDER HAS BEEN PLACED, THERE IS NO CANCELATION OF THIS ORDER. THERE ARE NO EXCEPTIONS TO THIS POLICY!

Smaller Lower Ball Joint Knuckles for Early Tundra and Sequoia Years use 10mm bolts with 14mm heads, if still Genuine spec.

6202-12 bearing

6300 bearing Dimensions

Turn a troublesome wheel-bearing maintenance job into a quick knuckle swap. With the Yota1 Pre-Assembled Steering Knuckles with new KOYO wheel bearings, you can easily replace your wheel bearings without using a press.

**WHEN PURCHASING THESE SPINDLES, WE ARE CUSTOM BUILDING THEM FOR YOUR VEHICLE, ONCE THE ORDER HAS BEEN PLACED, THERE IS NO CANCELATION OF THIS ORDER. THERE ARE NO EXCEPTIONS TO THIS POLICY!

*The 1st Gen Tundra and Sequoia have two different size steering knuckles. The early years 2000-2002 use a smaller lower ball joint. 2004 is a split year and 2005-2007 use a larger lower ball joint.

Fits smaller Lower Ball Joint: Tacoma 1995-2004 4Runner 1996-2002 Tundra 1999-2004 Sequoia 2001-2004 NOTE: Please reference the photos below to determine if you have the small early knuckles or larger later knuckles.