Dropped my car off at a mechanic to check into an issue I’ve been having (groaning in the front/left wheel). Turns out it is a wheel bearing that needs to be replaced and the mechanic quoted me $750 for the job, saying “the bearing needs to be pressed and it’s a fair amount of labor”.

You already know your car cannot function safely without sturdy and properly fit wheels. A wheel is complex, and several components must be integrated for it to function safely—including the bearings.

Not necessarily. I had this setup on my old Mazda Protege. You press the hub out of the bearing, and the inner race of the bearing is stuck in the hub. You then carefully score the outside of the inner race, and strike it once or twice with a chisel…the inner race splits in too, and you’re left with the hub, which you can press into the new bearing.

A wheel bearing is a set of steel balls held together in a metal ring called a race. The race is located inside the hub, and each wheel has one. At the center of the wheel is a hollow piece of metal called a hub. The wheel bearings fit tightly inside this hub and ride on a metal axle shaft, helping reduce friction when the wheel spins.

Yeah, tight but not pressed in I had to pry mine out a fraction at a time, going around to keep it from getting jammed. Both GM and an 03 Toyota Camry. The GM had a penta-socket head fastener on one side and a pressed in “rivet” on the other. Still struggling to understand/justify the need for such hardware…

Cool. With that said, you really should consider getting the other one replaced at the same time…see if the shop will give you a break on the labor.

Tire balancing is an important component of your routine automotive maintenance schedule. Like changing the oil, balancing the tires is something that vehicle owners are encouraged to do several times throughout the course of the year. This is also something you’ll want to make sure to have done by automotive service professionals. There are […]

Wheel Bearingcost AutoZone

This doesn’t include the cost of replacing one perfectly good ABS sensor that had to be destroyed in the process. (tech told me that the sensor would be in the way of the press, and they couldn’t remove it without destroying it. ). I believed him, as I replaced the ABS sensor on the other side a year earlier. It was defective. I too had to destroy the old one to remove it, as Toyota machined the hole too small. Talk about a tight fit! There was TSB about this, I believe.

If you want to know how to check for a bad wheel bearing, place your car on a jack stand, grip your hands on the 6 and 12 o’clock positions of the tire, and then spin the wheel to see if it wiggles. It’s also a great way to learn how to tell which wheel bearing is bad.

Frontwheel bearing replacement price

you can get the whole hub and bearing for like $150 , so your mechanic is telling you it is going to take him 5 hours to do the job on a bearing ?? I doubt it , i would run from that guy .

Should you invest the time and money required to have your vehicle’s suspension lowered? It’s a question that many drivers never even think about. Before you make the decision to proceed with lowering your vehicle’s suspension, consider the options and understand the pros and cons that a lowered suspension entails. Why Get a […]

Chevywheel bearing replacement price

Most people are aware of the need for general car maintenance. It’s essential to take care of the basics, like regular oil changes and checking battery terminals for corrosion. But, getting an alignment is just as important. Many think it’s simply a minor irritation when your alignment starts to get off. The truth […]

Keep in mind that wheel bearings are not the same as engine bearings, as there is no constant source of lubrication for wheel bearings. This means they must be tight enough to keep water and road dust out. They also support the entire vehicle weight while driving, so they endure abuse from rough roads and potholes, as well as lateral forces when turning.

As always when in doubt you get a second opinion . It could be that this shop does not have the right equipment for the job or there is a lot of labor involved .

Wheel bearing replacementnear me

You should also verify how many wheel bearings they’re replacing. If it were me, I would go ahead and replace the bearing on the other side of the vehicle as well…chances are, it’s not far behind in terms of failure.

Rearwheel bearing replacementcost

After I drilled out the defective sensor , I took a reamer to the hole. The shop that removed the other sensor (left front) was nice enough to let me go home without a sensor (I got one from an online Toyota dealer at a big discount). And my labor is free.

You did the right thing by getting other quotes and as an aside, never give a lot of credence to online reviews. Some may be fake and in some cases people may have been robbed blind and simply do not realize it. Their car is fixed for double what anyone else charges so they’re happy with it all.

They need to be tight due to the super tight tolerance on positioning for proper operation. I did some work recently and had to R&R an ABS sensor. Long story short, a thousandth made a huge difference in signal level. Too close and it rubs, too far and weak signal. Rust forming on the spacer was enough to cause weak signal…removing them required diligent care not to damage them…

Toyotawheel bearing replacementcost

Did you get an itemized estimate? If not, ask for one. Do that when you get a second opinion too. That way you can easily compare the two. Don’t tell the second shop what the other one estimated.

If you’re driving on the highway and a wheel breaks off, it’s because a wheel bearing failed. What are the signs of a bad wheel bearing, and what can you do about it? Here, we explore wheel bearings, including what they are, how they work, and how to tell if they’re about to fall off.

I thought sometimes they just replace the whole hub part is a little more but less labor. That price sounds high you need to get a second quote.

Elantra has same bearing setup as Honda’s. A shop can lowball the cost and then have to replace more parts or remove knuckle to press out bearing. The bearing is pressed into the hub. So, assume the hub will be damaged or scored.image600×600 22.3 KB

Wheel bearingnoise

Wheel bearing replacementcost Near Me

While most estimates suggest wheel bearings should last between 75,000 and 150,000 miles, the actual lifespan depends on:

You didn’t mention the year of your Elantra, but when I plugged in a 2015 into repairpal.com for an estimate, my local zip code brought up an estimate for $173-266 to change a single wheel bearing…you definitely need to get a 2nd and 3rd quote

Scope of work as per the first shop was to “replace the left/front wheel bearing and press the new one”, that’s all they mentioned.

Same with a guy I know in my area who passed away back in 2011. He BSed, cobbled together, hacked up, and in general screwed everyone over yet everyone within 25 miles of him praised his name to the mechanical heavens. Go figure…

I paid $250 parts and labor for the front wheel bearing of my previous Toyota Corolla. It had to be pressed in also. They put in a Timken bearing and it didn’t take much time…around 45 minutes and I was out of there.Shop around because your estimate seems on the high side.

I took my knuckle to a shop and they pressed out my bearing and he said hub was scored but he had 1 used. For $20. I tried to pay with my card and tech said hub was his and cash only. Had to run to atm for $20 cash. Bet tech had a few hubs in his toolbox. From other jobs?

Thanks all, appreciate the help. I did call a second and third shop and was quoted $350 by one and $380 from the other. Both shops gave me their estimate, and when they then asked what I was quoted when it was diagnosed they said the shop I went to was notorious for extremely high prices and that $750 was way too high… I’m surprised since the first shop had great reviews.

The amount of miles your vehicle can endure will depend on how extensive the damage is and the conditions on the road. If you’re concerned about replacement costs, note that the average estimate for a replacement is about $350 for each bearing.

If you notice signs of a bad wheel bearing, visit your nearest Meineke location. Once you bring your vehicle to us, we’ll perform a thorough diagnosis to honestly determine if a replacement is necessary.

The best advice is to head to your nearest auto shop that offers wheel repair and replacement services. If you’re on the road, slow down steadily and avoid turning rapidly. If you drive long distances on a bad wheel bearing, you’ll eventually lose control of the vehicle, and the wheel will stop suddenly.