This doesn’t include the cost of replacing one perfectly good ABS sensor that had to be destroyed in the process. (tech told me that the sensor would be in the way of the press, and they couldn’t remove it without destroying it. ). I believed him, as I replaced the ABS sensor on the other side a year earlier. It was defective. I too had to destroy the old one to remove it, as Toyota machined the hole too small. Talk about a tight fit! There was TSB about this, I believe.

Dropped my car off at a mechanic to check into an issue I’ve been having (groaning in the front/left wheel). Turns out it is a wheel bearing that needs to be replaced and the mechanic quoted me $750 for the job, saying “the bearing needs to be pressed and it’s a fair amount of labor”.

How unbearable, those bearings look like Lindor balls all melted up. I’m losing my bearings, I think it’s hazelnut Lindors, but i’m not sure if it’s Dark chocolate or not, or milk chocolate bearing a dark top layer. Bare with me here……….., cuz i don’t really care, I’ll eat them both.

Last year I was driving from Townsville to Brisbane. And about 800km in the wheel bearing on the rear right wheel went which shook the wheel completely off. I was only a learner at the time so it was the scariest thing that had happened to me while driving. The worst part was the car had just been serviced for the trip and the bearings had been replaced.

Not necessarily. I had this setup on my old Mazda Protege. You press the hub out of the bearing, and the inner race of the bearing is stuck in the hub. You then carefully score the outside of the inner race, and strike it once or twice with a chisel…the inner race splits in too, and you’re left with the hub, which you can press into the new bearing.

Yeah, tight but not pressed in I had to pry mine out a fraction at a time, going around to keep it from getting jammed. Both GM and an 03 Toyota Camry. The GM had a penta-socket head fastener on one side and a pressed in “rivet” on the other. Still struggling to understand/justify the need for such hardware…

You did the right thing by getting other quotes and as an aside, never give a lot of credence to online reviews. Some may be fake and in some cases people may have been robbed blind and simply do not realize it. Their car is fixed for double what anyone else charges so they’re happy with it all.

As always when in doubt you get a second opinion . It could be that this shop does not have the right equipment for the job or there is a lot of labor involved .

There’s a decent chance that at some point, you’ve had your car back from an MOT test and found a patch of orange on the results that says something along the lines of ‘play in offside front wheel bearing.’ It sounds scary - after all, in order of everything you want to function correctly on your car, the wheels are pretty far up the list.

Wheelbearings replacementcost

After I drilled out the defective sensor , I took a reamer to the hole. The shop that removed the other sensor (left front) was nice enough to let me go home without a sensor (I got one from an online Toyota dealer at a big discount). And my labor is free.

I took my knuckle to a shop and they pressed out my bearing and he said hub was scored but he had 1 used. For $20. I tried to pay with my card and tech said hub was his and cash only. Had to run to atm for $20 cash. Bet tech had a few hubs in his toolbox. From other jobs?

I feel dumb because I cant figure out how the bearings work with the rotating axle and how it doesnt just spin and the wheel not move.

The wheel bearing is housed within the hub assembly, providing the static connection with the hub carrier through an outer ring or ‘racer’. On driven wheels, the driveshaft travels from the transmission and passes through the centre of the wheel bearing through the inner ring, creating the rotational partnership. Ball-type bearings are generally used on the driven wheels of a vehicle, while tapered roller bearings, with cylindrical rollers arranged around an inner ring, are predominantly used on the non-driven wheels.

Frontwheel bearingreplacementcost

If left to wear down further, a wheel bearing could seize and lock the axle, causing all sorts of additional damage to the drivetrain. Worst-case scenario, the wheel may come off the car altogether, so it’s best to get the car looked at as soon as possible if you suspect a dodge bearing. However, considering the forces that a drivetrain has to counteract during its lifetime of usage, it is impressive how long wheel bearings can last if inserted properly and looked after - depending on the car, original bearings can generally last for comfortably over 100,000 miles.

Just a few months ago I’ve had the rear wheel bearings of my E36 replaced. When the mechanic popped them out, he said that the rear right bearing was shot beyond recognition and it was a miracle that it didn’t break.

Which means, that a few months prior, I’ve just hit 210 KPH with broken wheel bearings in what’s essentially a 20 years old coffin on wheels. Yay.

Thanks all, appreciate the help. I did call a second and third shop and was quoted $350 by one and $380 from the other. Both shops gave me their estimate, and when they then asked what I was quoted when it was diagnosed they said the shop I went to was notorious for extremely high prices and that $750 was way too high… I’m surprised since the first shop had great reviews.

Although it can be a labour-intensive job if one were to fail, the shift to selling entire hub assemblies should make a bad wheel bearing fixable from home, with a decent tool kit and a bit of know-how. So do not fret the next time that horrid whir begins to creep into the cabin, as a fix may be only a ratchet spanner away.

Wheel bearingreplacementcostNear Me

A car’s wheel bearing does this by using small metal balls or cylindrical rollers that roll between two smooth rings of metal. Helped along by grease, the bearing rotates in tandem with the wheel’s rotation, the rolling motion of the balls or rollers allowing the wheel hub to rotate as freely as possible. It also helps absorb some of the forces exerted on the car’s wheel during acceleration, braking and cornering.

Rearwheel bearingreplacementcost

They need to be tight due to the super tight tolerance on positioning for proper operation. I did some work recently and had to R&R an ABS sensor. Long story short, a thousandth made a huge difference in signal level. Too close and it rubs, too far and weak signal. Rust forming on the spacer was enough to cause weak signal…removing them required diligent care not to damage them…

© Crash Media Group Ltd 2024.The total or partial reproduction of text, photographs or illustrations is not permitted in any form.

Hey, i have driven a car to the limit where humming sound is so loud inside that you can’t even hear a Radio. They can last a long time before they go, even if they are shot.Also had an situation where from the moment bearing started to hum, till it disintegrated it self, it lasted about 2 km…. I guess it depends on how good brand you use and how lucky you are.

The most common mechanical failure is due to a seal leak, which allows the lubricating grease to exit the bearing, and water and grit managing to worm its way in. This all amounts to the degradation of the balls and the outer and inner housing of the bearing, often creating that gritty, skimming sound as the wheel is rotating. Looking inside a worn-out bearing, there will often be small specs of metal that have broken off from inside the bearing itself and are grinding their way around the racers, causing more damage. If you have had a minor shunt, it’s always worth having the hub assembly checked over afterwards.

How much a wheel bearing costnear me

Elantra has same bearing setup as Honda’s. A shop can lowball the cost and then have to replace more parts or remove knuckle to press out bearing. The bearing is pressed into the hub. So, assume the hub will be damaged or scored.image600×600 22.3 KB

Like all mechanical parts on a car that rotates, rub and roll, they tend to wear out eventually. There are several signs of a knackered wheel bearing. The most common is a constant drone, hum or growl from the affected wheel, which will get more noticeable as speed increases or the car turns. You may also notice less responsive steering or speed-dependent wheel wobble. On more modern cars, which often have anti-lock brake sensors integrated into the hub assembly, you might get an ABS warning light on the dash.

How much a wheel bearing costcalculator

Wheel bearings play an important role within the drivetrain of any vehicle, as they provide the first connection between the moving and static areas of the car. A bearing – in its simplest form – is a friction reduction device placed within something like a wheel to aid the efficiency of rotation. This is achieved as rolling produces much less friction force than sliding.

You should also verify how many wheel bearings they’re replacing. If it were me, I would go ahead and replace the bearing on the other side of the vehicle as well…chances are, it’s not far behind in terms of failure.

I paid $250 parts and labor for the front wheel bearing of my previous Toyota Corolla. It had to be pressed in also. They put in a Timken bearing and it didn’t take much time…around 45 minutes and I was out of there.Shop around because your estimate seems on the high side.

Same with a guy I know in my area who passed away back in 2011. He BSed, cobbled together, hacked up, and in general screwed everyone over yet everyone within 25 miles of him praised his name to the mechanical heavens. Go figure…

Wheel bearingreplacementcostCanadian tire

To replace a wheel bearing properly, it has to be popped out of the hub assembly, preferably using a hydraulic press. Problems can arise with the re-installation of the new bearing, as the alignment must be accurate to avoid the bearing wearing out rapidly and causing further pain.

Cool. With that said, you really should consider getting the other one replaced at the same time…see if the shop will give you a break on the labor.

You didn’t mention the year of your Elantra, but when I plugged in a 2015 into repairpal.com for an estimate, my local zip code brought up an estimate for $173-266 to change a single wheel bearing…you definitely need to get a 2nd and 3rd quote

I thought sometimes they just replace the whole hub part is a little more but less labor. That price sounds high you need to get a second quote.

Wheel bearings should last tens of thousands of miles, but many mechanics will simply hammer the bearing back into the hub assembly instead of precisely aligning it and using the aforementioned press. This will inevitably lead to the bearing not rotating in the perpendicular fashion that it was designed for, accelerating wear and damage to the part. It’s important, therefore, if you’re not 100 per cent confident in your own ability, to ensure you’re using a trusted, professional garage.

Did you get an itemized estimate? If not, ask for one. Do that when you get a second opinion too. That way you can easily compare the two. Don’t tell the second shop what the other one estimated.

Wheel bearings are generally made from hardened steel, so they can withstand a serious amount of rotational abuse. But apply heat (through lack of lubrication) or dirt and water (broken seal) and all hell can break loose (this is yet another reason to avoid driving through deep water). Hitting one too many potholes or taking speed bumps too quickly can also exert excessive force on your bearings, shortening their useful life.

you can get the whole hub and bearing for like $150 , so your mechanic is telling you it is going to take him 5 hours to do the job on a bearing ?? I doubt it , i would run from that guy .

Wheel Bearing costAutoZone

Most online parts stores will now sell the entire hub assembly with the wheel bearing pressed into it, saving the hassle and potential scope for mistakes within the specific bearing assembly. It goes without saying, but you should also make sure that, if possible, you or the garage is using an original manufacturer part or one of reasonably similar quality - this is one area you really don’t want to skimp on.

As long as you catch a wheel bearing issue early, though, it shouldn’t be a massively expensive or time-consuming fix, and if you’re decent with a spanner, it’s potentially something you can sort yourself. Here’s what a wheel bearing is, why it’s important, and how to tell if there’s something wrong with one.

They never seize immediately. No need to fear. I have a comparison to make. My Skoda had 5 out of 4 changed in its 175 000 km lifetime. Only one bearing failure might have been caused by an accident. My E46 has had the originals for 245 000 km and 13 years. And none of them seems to be on their way out.

Scope of work as per the first shop was to “replace the left/front wheel bearing and press the new one”, that’s all they mentioned.