In-store RETURNS. If you need to return or exchange any item that has not been discounted, please note you must do so within 14 days of purchase: with the receipt! All items returned must be in the original condition that they were received—NOT WORN, ALTERED OR WASHED, and must have ALL TAGS and the original packaging. The return item(s) must be free and clear of odors, lint, and pet hair. We have the right to reject/refuse any returns or exchanges if we believe the item(s) have been altered in away way.

How much grease to put in asealedbearing

Note: The convenient lubrication provisions of the E‑Z Lube® and the oil lubrication must not replace periodic inspection of the bearings.

Pro-tip: The E-Z Lube feature is designed to allow immersion in water. Axles not equipped with E-Z Lube are not designed for immersion and the bearing should be repacked after each immersion. If hubs are removed from an axle with the E-Z Lube feature, it is imperative that the seals be replaced BEFORE bearing lubrication. Otherwise, the chance of grease getting on brake linings is greatly increased.

How much grease to put in a bearingcalculator

To increase the life of your Dexter axle, Dexter highly recommends that you perform annual bearing grease and oil as outlined in the maintenance schedule page 85. While attempting to do these service checks, keep in mind the importance of safety. If you are familiar with truck and trailer maintenance, feel free to follow the instructions below. If you do not feel confident performing truck or trailer maintenance, please take your vehicle to a service center to avoid injury. Closely follow along below with the correct procedures performed for each lubrication type.

On-line RETURNS -- There will be a restocking fee of $15 per item on all refunds or exchanges via on-line purchases. If you need to return or exchange any item that has not been discounted, please note you must do so within 14 days of purchase: with the receipt! All items returned must be in the original condition that they were received—NOT WORN, ALTERED OR WASHED, and must have ALL TAGS and the original packaging. The return item(s) must be free and clear of odors, lint, and pet hair. We have the right to reject/refuse any returns or exchanges if we believe the item(s) have been altered in away way. Once the item(s) has been received back to Mocean, we will determine the refund/exchange less the restocking fees. Buyer is responsible for all shipping costs! If the refund/exchange is approved, Mocean will refund/exchange the funds/item(s) back to the original purchasing party/payee/payment type within 14 days after receiving!  We will notify you via email or phone.

SKFbearinglubrication Calculator

How much grease to put in a bearingreddit

We are not responsible for stolen packages; if your tracking number shows your items have been delivered and you have not received the package, you must contact your mail carrier and file a claim. Mocean is not responsible for missing, damaged and/or stolen packages.

First, you will need to remove the rubber plug from the end of the grease cap. Then place a standard manual grease gun onto the grease fitting located at the end of the spindle. Do not use pneumatic powered grease guns as these can inject grease too fast and force grease past the seal, or in rare cases dislodge the seal. You will want to make sure the grease gun nozzle is fully engaged on the fitting. While you rotate the hub, pump the grease slowly into the fitting. The old, displaced grease will begin to flow back out the cap around the grease gun nozzle. When the new clean grease begins to come out, remove the grease gun, wipe off any excess, and replace the rubber plug in the cap.

The material provided by Dexter® is intended for informational purposes only. The information on these pages is provided on an "as is" basis without warranty of any kind, either expressed or implied, including without limitation warranties. Dexter® assumes no liability or responsibility for any errors or omissions in the website's content. Dexter® shall not be liable for damages(whether compensatory, punitive, direct, indirect, special, incidental, or consequential) to any user regarding the website content. Any user agrees to indemnify and hold Dexter® harmless from any and all claims, actions, or other proceedings (including attorney fees and court costs) arising out of the use of the website.

SKFbearing greasequantity chart

CAUTION: Do not mix lithium, calcium, sodium, or barium-complex greases due to possible compatibility problems. When changing from one type of grease to another, it is necessary to ensure all the old grease has been removed.

You can contact us via email at moceanskateboards@gmail.comwith any questions or call our shop during business hours at 207-210-2706. Mocean™ LLC

If your axles are equipped with oil-lubricated hubs, periodically check, and refill the hub as necessary with a high-quality hypoid gear oil to the level indicated on the clear plastic oil cap. The oil can be filled from the oil fill hole, if present, in the hub to through the rubber plug hole in the cap itself.

Whenever the hub is removed, inspect the seal to assure that it is not nicked or torn and is still capable of properly sealing the bearing cavity. If there is any question of condition, replace the seal. Use only the seals specified in our seal chart.

Proper lubrication is essential to the proper function and reliability of your trailer axle. Bearings should be lubricated every 12 months or 12,000 miles. You should repack your bearing cone by placing a small amount, roughly the size of a half-dollar, of grease into the palm of your hand. Then press a section of the widest end of the bearing into the outer edge of the grease pile close to the thumb forcing grease into the interior of the bearing. You will need to repeat this while rotating the bearing from roller to roller. You should continue this process until the entire bearing is filled with grease. Before you reinstall the bearing, make sure you apply a light coat of grease to the bearing cup.