Replace the wheel and tighten the lug nuts by hand. Support the vehicle with a floor jack and remove the safety jack stands. Slowly lower the vehicle until its tires just touch the ground (similar to how you would when changing a flat tire).

Place the rotor face down on the floor with the back side facing upwards. Take the new larger bearing and rub the bearing grease into the casing.

Replace the retaining nut on the spindle and grab the rotor with both hands. Proceed to pull the rotor off the spindle, allowing the larger inner bearing to get caught on the retaining nut. Then, release the bearing and grease seal from the rotor.

Place the new bearing into the back of the rotor and apply grease to the inside bearing cavity. Install a new bearing seal over the new larger bearing and slide the rotor back on to the spindle. (A rubber mallet can be used to tap the bearing seal into place, if needed).

To do this, use your pliers to remove the cotter pin and retaining nut and then slide the rotor forward to release the outer wheel bearing (smaller wheel bearing).

To do this, use your ratchet and ⅜ -socket set to unbolt the disc brake caliper and bracket from the spindle. Use a screwdriver to remove the caliper itself.

FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories.  Shipping is not available to Canada. Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses.  Final shipping costs are available at checkout.

To loosen your lug nuts, you will need a ½ inch ratchet with the correct size socket. Loosen the lug nuts, but do not remove them fully just yet.

Now that the new bearing is installed, the brake rotor and caliper can be placed back onto the vehicle using a ratchet and the appropriate sockets that were used to remove them.

Pack the new smaller bearing with grease and slide it on to the spindle inside the rotor. Now install the thrust washer and retaining nut onto the spindle.

Don’t stress too much if your car is giving you that tell-tale sign, because it shouldn’t be a costly repair. While changing your bearings is considered a more involved job, for most it can still be done at home to avoid a trip to the mechanic. But be warned, you will need a few specialty tools to get the job done right.

You are almost there! Just a few last steps that are important to give your full attention to in order to wrap this maintenance up safely.

FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories.  Shipping is not available to Canada.

We’re going to share how to change your wheel bearings in a more general step-by-step process for the common wheel bearing types that are found in the majority of vehicles. However, before starting your replacement job, please consult your vehicle’s service manual to ensure you know what kind of bearings you’re working with on your specific vehicle.

Wheel bearings are sets of steel balls that are housed in metal casings called races, which are located in the wheel’s hub.

Congratulations, you have successfully changed your vehicle’s wheel bearing. It is important to perform a test drive after changing the wheel bearings to ensure that the repair is complete.

Be sure to refer to your owner's manual for information on where the proper lift points to jack up your vehicle are located.

Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.

Use a torque wrench to tighten the lug nuts to manufacturer specifications. Lower the vehicle completely and remove the floor jack.

Then be sure to use a wheel chock to block the tire opposite of the wheel that you will be working on first. For example, if changing the driver’s side front bearings first, you will need to chock the passenger’s rear wheel.

Use a floor jack and a pair of safety jack stands to lift your vehicle. This lets you safely remove the tires for your bearing replacements.

Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses.  Final shipping costs are available at checkout.

If the wheel bearings are housed inside your disc brake rotor, which is common to see in trucks, you will need to pry off the central dust cap to expose the cotter pin and retaining nut.

Learning how to change your wheel bearings can be considered by some to be a bit more involved than your entry level maintenance on your truck or car. However, with these tips, you should be able to accomplish this task successfully and save yourself some money!

After gathering the supplies needed, you will need to prepare your vehicle to safely change the wheel bearings. Start by parking your vehicle on a level surface before you begin.

Once you have all of the wheel bearing components removed, it is time for the fun part – the actual installation of your new wheel bearings.

This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

If your bearing is housed inside a hub that can be unbolted, simply use your ratchet to unbolt the hub from the spindle and install a new hub.

Pro Tip: When removing the caliper, be careful not to let it dangle freely because that can damage the flexible brake line. Instead, use the wire hanger to hook it on a secure part of the undercarriage or hang the brake caliper on the suspension.

The biggest tell on when it’s time to change your wheel bearings and a sign that they are starting to fail is when you hear a moaning noise coming from this area while driving.

Tighten the retaining nut until it is snug and turn the rotor counterclockwise at the same time. Tighten the retaining nut a ¼ turn past snug and then install a new cotter pin.

In most cases, this service can be done inexpensively. Once the new bearing is pressed in, the spindle can be installed back on to the vehicle.

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov

High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Lifetime Warranty This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

The rotor mounts on a hub that contains the pressed-in wheel bearing. Bearing assemblies on front or rear non-driven axles are mounted between a wheel hub and a simple spindle shaft. Some cars have permanently sealed front wheel bearings.

Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions. High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle. Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function. Highest Quality MaterialsMade from highest quality materials that meet or exceed OEM standards Quality Tested - built to a strict level of product standards.

If your bearing is pressed into the spindle, it is recommended that you remove the spindle from the vehicle and take both the spindle and the new wheel bearing to your local repair shop. They will have the specialty tools to press out the old bearing and press in the new one.

If you encountered any problems while changing your wheel bearings, or if you are not comfortable completing this maintenance on your own, be sure to call a professional mechanic.