Then the washer will fit over the bearing before the castle nut goes back on. The flat spot on the washer should fit perfect on the flat part of the axle so the washer stays in place while underway.

You might be able to salvage the cotter pin but over time the metal will be fatigued. It is best to buy 4 new cotter pins and replace them each time.

Drop the inner bearing in the same way you took it out. It should fit in place so each bearing rides flat against the race.

Wheel bearings are a set of steel balls contained in a lubricated metal ring located in the hub. They support the weight of your vehicle and allow the wheels to rotate freely while you drive. In normal conditions, the bearing accomplishes this without making any excessive noise. If the grease lubricant escapes the bearing or debris as water or sand enters it, the bearing will wear out and fail quickly.

While I am in there, I like to give my brakes a good cleaning with some brake cleaner. Once that’s done, we can turn our attention back to the hub.

The short answer is no. You should not drive your vehicle if you believe you have bad wheel bearing. The long answer is yes, but with the understanding that driving with a failed or failing wheel bearing can lead to serious safety issues as well as severe damage to your car.

How togrease wheel bearings without removing

Using a small flat-head screw driver, pry the grease cap off of the end of the axle. Work around it evenly until you starts to see the gap widening.

With the grease seal out, you can pull out the inner bearing. Again, my bearing still has lots of grease in it which tells me I did not wait too long to repack it.

After owning our Airstream for 5 years, I finally decided that it might be a good idea for me to learn to repack my own bearings. It is one of the chores that I have always wanted to learn but never committed enough time and effort to figure it out. During our trip through Wyoming in 2013, our friends Josh and Jessa lost a bearing and had a wheel come apart. Fortunately no other damage was done. We managed to make the repair ourselves on the road and in the meantime, learned a thing or two about wheel bearing maintenance.

WheelBearingpacking tool

Without damaging the grease cap, remove it form the end of the axle. It should come off without much hassle. If you notice any damage or if you suspect that the grease cap will not stay in when put back on, you will need to replace it with a new one.

Slowly work all the way around until the seal comes off. Chances are, you are not going to reuse the old seal. You can tell the little dimples the seal puller made while I was removing it.

Right there on the outside is one of the brake shoes for this electric brake. There are 2 per wheel on opposite sides of the assembly. Looks like I have a fair amount of shoes left.

With the castle nut off, the washer and the outer bearing should come right off. You can see that the bearing has a tapered shape as it is held in by the washer and castle nut. That tapered shape is how the hub is held on to the axle. If that outer bearing fails and wears away, your entire wheel will no longer be held to the axle and will freely move away from the trailer. That failure is usually due to loss of grease in the bearing and extreme temperatures to literally wear the bearing down to metal dust.

With the wheel off, you will see the hub assembly. Most of these items will be coming off and we will start with the grease cap.

When the bearing fails and comes apart, it will cause play in the wheel. This can lead to severe instability when driving at high speeds and can come on suddenly if the bearing completely fails while you drive.

This is an extreme case, but if you drive on a bad wheel bearing for long enough, the wheel could come off. If this were to happen on the freeway or at high speeds, it could be catastrophic for you, your car, and other drivers.

I hope this has help some of you at least in learning how this process is done.  It is time consuming especially if you have 2 or more axles. It probably takes me about 2-3 hours to do the entire job. If you have someone you trust to be able to do a good job then by all means have a professional do it. If you are like me, sometimes this needs to be done while on the road, I prefer to know that I am responsible in doing the best possible job to ensure my family is safe on the road. I have heard from at least two different full time travelers who have had axle failures that the issue ultimately came down to issues in the last bearing packing job. Please feel free to contact us if you have any questions or suggestions about how to repack your own bearings. Happy travels!

Here is the inner bearing back in place. It should drop right in without any trouble and it will be held in place by the new grease seal until the wheel is back on the axle.

With the cotter pin removed, the castle nut should come off pretty easily. It should not be on very tight. You might need to use a wrench initially but mostly you should be able to work it off by hand. As you can tell, mine still has lots of grease in there so it came off easily.

Some of these parts are optional to replace while performing this job but you will definitely need these following items. Make sure you look up exactly what size and part number you need for your axle so you have everything you need before getting started:

Repackwheel bearings cost

With the bearings out, set them on a clean surface. We will pack these full of new grease in a minute and reinstall them.

If the noise you are hearing continues when you come to a stop, it is likely not caused by a bad wheel bearing. To produce noise, the wheels of your car need to be rotating.

Being part of the hub assembly, noise caused by a bad wheel bearing will only occur when you are moving. The sound may increase or decrease when you pick up speed or go around a turn. Paying attention to changes in noise or volume when going around corners. These changes can give insight into which side has gone failed. A bad wheel bearing can make any of the following noises depending on the cause or severity of the failure:

The brake discs on your car are part of the rotating assembly connected to the hub and wheel bearing. When your wheel bearing has failed to the point of lateral play, the disc will no longer be aligned correctly. This means when you press the pedal, it may feel soft and take longer for your car to stop.

First off, this is something that needs to be done for preventive purposes. You will not have any indications of bearing failure until it is catastrophic. The rule of thumb is once-a-year or every 10,000 miles. Doing it more often will not hurt. If you are not up to doing this job yourself, this can easily be done by any trailer or RV repair shop or even a mobile RV repair man. I decided that learning to do this myself not only will save me money, it will also give me a peace of mind to know that no one cut corners or hurried through the job as it is a serious matter of safety as our family travels around the country.

BearingPacker

A lot of the time, your car may not feel any different when the bearing is making noise. It’s easy to overlook or put off an issue that is not directly impacting your daily driving.

Here is the stub axle. Give it a good wipe down with some paper towels and inspect it for wear. If you do not let your bearings go too long without repacking, it should be in good shape. You are looking for any abnormal marring on the axle surface.

When in doubt, bring your car to a technician. When it comes to wheel bearings, it’s better to be safe than sorry. If you aren’t sure whether the sound you are hearing is a bad wheel bearing, the technicians at Matson Point S will take a look and let you know exactly what is wrong with your car. Give us a call or schedule an appointment at our Riverton, Utah location today!

Hearing any abnormal noise while you drive is stressful. With so many moving parts making up your car, it can be nearly impossible to tell where that humming, whining, or whirring noise is coming from. A common issue that many drivers run into is a failing wheel bearing, which can present in a variety of ways. While many potential issues can cause an unusual noise while you drive, a bad wheel bearing is one possibility.

How topack wheel bearings onatrailer

Here is the axle with the electric brake assembly still attached. We will not need to take this down any further unless you need to replace your brakes. This is a good time to check their serviceability.

BearingBuddy

Now thread the castle nut back on the axle. The nut should go on just hand tight. Once it is in all they way, try to wiggle the hub side to side, back and forth with both hands while it is on the axle. It should not slide around too much. A good rule of thumb here is to snug it all the day down by hand until there is no play in the axle and then back it off about 1/8 turn or to the previous slot in the castle nut for the cotter pin to go in. Spin the hub around the axle by hand several turns to make sure the bearings are seated properly against the races. Check after several spins to make sure it moves smoothly with no feeling of grit and there isn’t too much wiggling back and forth. Repeat this process a couple of times until the hub spins and moves consistently after each test. Take your cotter pin and insert it into the hole in the end of the axle and it will hold the castle nut in place and prevent it from backing out.

Here is the cleaned races inside the hub. Some people recommend that it doesn’t hurt to grease up the races and interior of the hub as well. The idea is that the grease seal and grease cap will not allow any grease to escape and foreign objects to get in so it should not matter. Do that if it makes you feel better.

Before you do anything, choose a side you are going to start on and chock up the wheels on the opposite side of the trailer so doesn’t move on you. Pick a wheel to start and loosen the lug nuts with your tire iron or socket and breaker bar.

[…] do all the hubs.  To get a very concise description you can check out Dan from Malimish.com on the blog post he did regarding this.  He does an excellent job covering it all.  And Mark agrees with him that […]

Once your wheel is off the ground, completely remove all of the lug nuts and remove the wheel. So far, you are doing the exact same thing as if you were just changing a tire.

How to repackwheel bearings

This right here is the magnet that actuates the brakes. When your brake controller applies voltage to your electric brakes, the magnet sticks to the hub which causes the brake shoes to spread against the inner surface of the drum. The stronger the voltage, the harder the magnet pulls on the hub which applies more brake pressure against the drum. If you need to change your brakes, it is often best to order the entire electric brake assembly rather than replacing its parts. Since I am not replacing my brakes at this moment, we will not go much more into that.

Take a look at the interior of the hub from the inner-bearing side. Give it a good wipe with a paper towel to make sure there aren’t any foreign objects like metal shavings or rocks that got in there. You might be able to tell that on the inside of the hub, there are 2 rings of shiny metal that the bearings ride against. Those are called ‘races’. These races are made of harden steel. They are the contact surfaces of the hub against the fast spinning bearings when the trailer is moving. They don’t need to be replaced if the surfaces are smooth like mine. Sometimes if they have been damaged, you will need to replace them. Damage can happen when foreign objects make its way inside this space and gets cause between the bearings and races. That typically means you waited too long and the seal failed to let objects in and grease out. That is a job that requires a hydraulic press. If you see significant wear on those races, bring the hubs to an automotive repair shop with new sets of races and ask them to remove the old ones and press in the new ones. It should be about an hour of work so it should only cost you their minimum labor charge. Most of the time, you don’t need to worry about them.

Remember, a bad bearing will make the same noises no matter what road surface you are on. If you hear a noise that changes when you get on a more smooth or more rough road, you might be hearing tire noise.

The hub is also the brake drum that the brake shoes push against to slow the trailer down. You can see on the inside that there are polished surfaces. That is where the shoes and magnets make contact. Set the hub/drum aside for the moment and we will turn our attention back to the axle.

Here is the inside of the hub. This tool is called a grease seal puller. You can buy this at pretty much any auto parts store. You are going to need something that can pull out the old grease seals without damaging the bearings that are inside and this is the tool. This seal is what prevents grease from leaking out from the inside of the hub while the grease cap out the outside that we pried off earlier does the same job on the other end. Most bearing failures happen when one of the two fail and grease seeps away causing the bearings to overheat.

That is it! Now you are back to just putting the tire back on. From here on out, it is again just like if you were changing a tire.

How topack wheel bearings by hand

That being said, when you are moving, the sound will not cut in or out. If you only hear a noise when you are accelerating, decelerating, or braking, there may be another drivetrain issue.

Once the hub is back on, slide in the outer bearing. Pay attention to how the bearing goes in. The tapered side should go in first.

Here is the new grease seal. Pay attention to how the old one came out. The new one will need to go in the same way. They are NOT reversible.

This can be done pretty much anywhere you can find a level concrete or asphalt surface. Since you will be removing tires and wheels off of your trailer, it is not recommended for you to do this on an incline or soft surfaces. Other than that, a minimal set of tools are needed:

[…] and done well by myself. I documented the job on one of the wheels to illustrate to you my process. Click here to read all about it. […]

Once your tire is back on, hand snug the lug nuts before lowering the trailer from the jack. Once the tire is back on the ground, snug your lug nuts up to the specified torque settings. Now just repeat this 3 more times and you are done. Just as with any tire change, check your lug nuts to make sure they are still properly torqued down after 25 miles. It doesn’t hurt to check again at 100 miles just to be safe.

Take your grease cap and tap it back on with a rubber mallet. Again, this should go back on snugly. If it feels like it can come off on its own while traveling, considering replacing it. The last thing you need is this cap coming off and all of the grease inside the bearings spinning out.

With the inside of the hub wiped clean, now we can actually do the repacking of the bearings. Some people like to just replace the bearings with new ones each time but that is really not necessary. Just like the races, the bearings can last many, many years if they are maintained regularly. High quality bearings can be expensive but should also last a long time. To repack them, wipe the old grease off of the surface and reapply with new grease. You will want to work as much grease into these bearings as you can. That means you want all the little voids outside and inside of the bearing full of new grease. Put a glob of high-temperature bearing grease in the middle of your hand and just start to roll and push each bearing against your palm until you feel that the bearing is saturated. Do it for as long as you feel it is necessary. You can also use a bearing packer to do this job if you don’t think you can do it well enough by hand. It is a handy tool to have if you think you will be doing this a lot.

Once the lug nuts are loose, jack up the axle of the wheel you are working on. Alternatively, you can hitch up and roll the wheels on the other axle up some leveling blocks until the wheel you are working on is off of the ground. On mine, it takes 4 lynx leveling blocks to make that happen.