You did the right thing by getting other quotes and as an aside, never give a lot of credence to online reviews. Some may be fake and in some cases people may have been robbed blind and simply do not realize it. Their car is fixed for double what anyone else charges so they’re happy with it all.

Toyotawheel bearingreplacementcost

202361 — Therefore, taking into account perceived stress and dark personality traits can ... & Grafe, L. A. (2021). Sex differences in stress-induced sleep ...

Shop for Wheel Bearing Greases in Automotive Greases. Buy products such as TRIAX Spheron Grease - Super Heavy Duty, Red, High Temp, Ultra Tacky, ...

I took my knuckle to a shop and they pressed out my bearing and he said hub was scored but he had 1 used. For $20. I tried to pay with my card and tech said hub was his and cash only. Had to run to atm for $20 cash. Bet tech had a few hubs in his toolbox. From other jobs?

How to change a wheel bearing

Scope of work as per the first shop was to “replace the left/front wheel bearing and press the new one”, that’s all they mentioned.

They need to be tight due to the super tight tolerance on positioning for proper operation. I did some work recently and had to R&R an ABS sensor. Long story short, a thousandth made a huge difference in signal level. Too close and it rubs, too far and weak signal. Rust forming on the spacer was enough to cause weak signal…removing them required diligent care not to damage them…

Wheelbearings replacementcost

These closures are not always essential; however shielded and sealed bearings provide much better protection from contamination and help retain the bearing ...

Yeah, tight but not pressed in I had to pry mine out a fraction at a time, going around to keep it from getting jammed. Both GM and an 03 Toyota Camry. The GM had a penta-socket head fastener on one side and a pressed in “rivet” on the other. Still struggling to understand/justify the need for such hardware…

Did you get an itemized estimate? If not, ask for one. Do that when you get a second opinion too. That way you can easily compare the two. Don’t tell the second shop what the other one estimated.

You should also verify how many wheel bearings they’re replacing. If it were me, I would go ahead and replace the bearing on the other side of the vehicle as well…chances are, it’s not far behind in terms of failure.

I feel a loud grinding/crunching noise coming from the front passenger wheel but is felt through the shifter / transmission tunnel.

Cool. With that said, you really should consider getting the other one replaced at the same time…see if the shop will give you a break on the labor.

Apr 1, 2006 — 150 ftlbs MINIMUM no need to do any diagnostics, just start with the most expensive part and move toward the cheaper ones.

Elantra has same bearing setup as Honda’s. A shop can lowball the cost and then have to replace more parts or remove knuckle to press out bearing. The bearing is pressed into the hub. So, assume the hub will be damaged or scored.image600×600 22.3 KB

Wheel bearingreplacementcostNear Me

you can get the whole hub and bearing for like $150 , so your mechanic is telling you it is going to take him 5 hours to do the job on a bearing ?? I doubt it , i would run from that guy .

Same with a guy I know in my area who passed away back in 2011. He BSed, cobbled together, hacked up, and in general screwed everyone over yet everyone within 25 miles of him praised his name to the mechanical heavens. Go figure…

This doesn’t include the cost of replacing one perfectly good ABS sensor that had to be destroyed in the process. (tech told me that the sensor would be in the way of the press, and they couldn’t remove it without destroying it. ). I believed him, as I replaced the ABS sensor on the other side a year earlier. It was defective. I too had to destroy the old one to remove it, as Toyota machined the hole too small. Talk about a tight fit! There was TSB about this, I believe.

Frontwheel bearingreplacementcostNear me

Thanks all, appreciate the help. I did call a second and third shop and was quoted $350 by one and $380 from the other. Both shops gave me their estimate, and when they then asked what I was quoted when it was diagnosed they said the shop I went to was notorious for extremely high prices and that $750 was way too high… I’m surprised since the first shop had great reviews.

As always when in doubt you get a second opinion . It could be that this shop does not have the right equipment for the job or there is a lot of labor involved .

The same is true of your engine. Making sure your timing belt or belt tensioner is working properly and in good condition can help prevent costly repairs down ...

Interchange | Interchange Fourth Edition is a four-level series for adult and young-adult learners of American English from the beginning to the ...

Rearwheel bearingreplacementcost

Wheel Bearing costAutoZone

I thought sometimes they just replace the whole hub part is a little more but less labor. That price sounds high you need to get a second quote.

Jun 17, 2022 — 6 Answers 6 · If it is a carbon wheel it is worth rebuilding with new hub: If it is only the bearing has worn out, just replace the bearing and ...

After I drilled out the defective sensor , I took a reamer to the hole. The shop that removed the other sensor (left front) was nice enough to let me go home without a sensor (I got one from an online Toyota dealer at a big discount). And my labor is free.

You didn’t mention the year of your Elantra, but when I plugged in a 2015 into repairpal.com for an estimate, my local zip code brought up an estimate for $173-266 to change a single wheel bearing…you definitely need to get a 2nd and 3rd quote

For a national average across all vehicles, the average cost to replace the wheel bearings (for 1 wheel) is about $350 ...

Frontwheel bearingreplacementcost

Not necessarily. I had this setup on my old Mazda Protege. You press the hub out of the bearing, and the inner race of the bearing is stuck in the hub. You then carefully score the outside of the inner race, and strike it once or twice with a chisel…the inner race splits in too, and you’re left with the hub, which you can press into the new bearing.

Dropped my car off at a mechanic to check into an issue I’ve been having (groaning in the front/left wheel). Turns out it is a wheel bearing that needs to be replaced and the mechanic quoted me $750 for the job, saying “the bearing needs to be pressed and it’s a fair amount of labor”.

I paid $250 parts and labor for the front wheel bearing of my previous Toyota Corolla. It had to be pressed in also. They put in a Timken bearing and it didn’t take much time…around 45 minutes and I was out of there.Shop around because your estimate seems on the high side.

Feb 9, 2024 — Wheel bearings play an important role within the drivetrain of any vehicle, as they provide the first connection between the moving and static ...