If your bearing is pressed into the spindle, it is recommended that you remove the spindle from the vehicle and take both the spindle and the new wheel bearing to your local repair shop. They will have the specialty tools to press out the old bearing and press in the new one.

Unless required to do otherwise by law, we only collect your information in order to provide you with the information and services which you request. We will only send further information to you in the future if it is explicitly requested. We will provide you with the opportunity to unsubscribe from any future electronic communication.

12.7 mmbearingcross reference

We will not disclose your personal information to any individual, company or organisation (except as required by law). We do not share email or address information with other businesses or organisations.

If you encountered any problems while changing your wheel bearings, or if you are not comfortable completing this maintenance on your own, be sure to call a professional mechanic.

If you have any particular, unusual or sensitive enquiries with regard to privacy matters, email our Privacy Officer at contact@tools.com

12.7 mmbearingequivalent

Pack the new smaller bearing with grease and slide it on to the spindle inside the rotor. Now install the thrust washer and retaining nut onto the spindle.

Pro Tip: When removing the caliper, be careful not to let it dangle freely because that can damage the flexible brake line. Instead, use the wire hanger to hook it on a secure part of the undercarriage or hang the brake caliper on the suspension.

Welcome to tools.com, If you continue to browse and use this website, you are agreeing to comply with and be bound by the following terms and conditions of use, which together with our privacy policy govern tools.com’s relationship with you in relation to this website. If you disagree with any part of these terms and conditions, please do not use our website.

Congratulations, you have successfully changed your vehicle’s wheel bearing. It is important to perform a test drive after changing the wheel bearings to ensure that the repair is complete.

6203bearingdimensions

The biggest tell on when it’s time to change your wheel bearings and a sign that they are starting to fail is when you hear a moaning noise coming from this area while driving.

We’re going to share how to change your wheel bearings in a more general step-by-step process for the common wheel bearing types that are found in the majority of vehicles. However, before starting your replacement job, please consult your vehicle’s service manual to ensure you know what kind of bearings you’re working with on your specific vehicle.

Tighten the retaining nut until it is snug and turn the rotor counterclockwise at the same time. Tighten the retaining nut a ¼ turn past snug and then install a new cotter pin.

Place the rotor face down on the floor with the back side facing upwards. Take the new larger bearing and rub the bearing grease into the casing.

tools.com is committed to following best practices in protecting your personal privacy. We hope the following statement outlines clearly how we collect, use and protect the personal information which you provide to us.

In most cases, this service can be done inexpensively. Once the new bearing is pressed in, the spindle can be installed back on to the vehicle.

When you look at the tools.com website, we may record the following information for statistical purposes: - your ISP address - your top level domain name (for example .com, .gov, .au, .uk etc) - the pages you accessed and documents downloaded - the previous site you have visited - the type of browser you are using

Then be sure to use a wheel chock to block the tire opposite of the wheel that you will be working on first. For example, if changing the driver’s side front bearings first, you will need to chock the passenger’s rear wheel.

We will only collect information about you with your consent. When you browse our website, you do so anonymously. We do not collect information about you or your email address without your consent. We do not use cookies to collect information about how you use our site.

Replace the wheel and tighten the lug nuts by hand. Support the vehicle with a floor jack and remove the safety jack stands. Slowly lower the vehicle until its tires just touch the ground (similar to how you would when changing a flat tire).

We believe you have a right to know about what information organisations have about you. If you wish to access a copy of the personal information about you held by tools.com, please contact us at contact@tools.com

To do this, use your ratchet and ⅜ -socket set to unbolt the disc brake caliper and bracket from the spindle. Use a screwdriver to remove the caliper itself.

You are almost there! Just a few last steps that are important to give your full attention to in order to wrap this maintenance up safely.

Be sure to refer to your owner's manual for information on where the proper lift points to jack up your vehicle are located.

Learning how to change your wheel bearings can be considered by some to be a bit more involved than your entry level maintenance on your truck or car. However, with these tips, you should be able to accomplish this task successfully and save yourself some money!

If your bearing is housed inside a hub that can be unbolted, simply use your ratchet to unbolt the hub from the spindle and install a new hub.

12.7 mmbearingdimensions

To loosen your lug nuts, you will need a ½ inch ratchet with the correct size socket. Loosen the lug nuts, but do not remove them fully just yet.

To do this, use your pliers to remove the cotter pin and retaining nut and then slide the rotor forward to release the outer wheel bearing (smaller wheel bearing).

If the wheel bearings are housed inside your disc brake rotor, which is common to see in trucks, you will need to pry off the central dust cap to expose the cotter pin and retaining nut.

Use a floor jack and a pair of safety jack stands to lift your vehicle. This lets you safely remove the tires for your bearing replacements.

Wheel bearings are sets of steel balls that are housed in metal casings called races, which are located in the wheel’s hub.

Once you have all of the wheel bearing components removed, it is time for the fun part – the actual installation of your new wheel bearings.

Place the new bearing into the back of the rotor and apply grease to the inside bearing cavity. Install a new bearing seal over the new larger bearing and slide the rotor back on to the spindle. (A rubber mallet can be used to tap the bearing seal into place, if needed).

Now that the new bearing is installed, the brake rotor and caliper can be placed back onto the vehicle using a ratchet and the appropriate sockets that were used to remove them.

12.7 mmbearingsize

The rotor mounts on a hub that contains the pressed-in wheel bearing. Bearing assemblies on front or rear non-driven axles are mounted between a wheel hub and a simple spindle shaft. Some cars have permanently sealed front wheel bearings.

Replace the retaining nut on the spindle and grab the rotor with both hands. Proceed to pull the rotor off the spindle, allowing the larger inner bearing to get caught on the retaining nut. Then, release the bearing and grease seal from the rotor.

Use a torque wrench to tighten the lug nuts to manufacturer specifications. Lower the vehicle completely and remove the floor jack.

The term ‘tools.com’ or ‘us’ or ‘we’ refers to the owner of the website whose registered office is 134 Wellingon Pde, East Melbourne. Our ABN is . The term ‘you’ refers to the user or viewer of our website.

After gathering the supplies needed, you will need to prepare your vehicle to safely change the wheel bearings. Start by parking your vehicle on a level surface before you begin.

Don’t stress too much if your car is giving you that tell-tale sign, because it shouldn’t be a costly repair. While changing your bearings is considered a more involved job, for most it can still be done at home to avoid a trip to the mechanic. But be warned, you will need a few specialty tools to get the job done right.

tools.com provides links to websites outside of this site. These linked sites are not under the control of tools.com, and we are not responsible for the conduct of companies or organisations linked to our website. Before disclosing your personal information on any other website, we advise you to examine the Terms and Conditions of those websites.