If you're puller is going to use the threads of the hub that is stuck on the axle....I'd suggest using longer bolts backed up with washers and nuts from the back side as well. Some of these pics have them. It will take a lot of the stress off the threads in the hub, and help alleviate stretching or stripping the threads in the hub. Heat is a big help as well. Be cautious about it though. You will need a good amount, but too much is bad for other things as well..

Wheelbearingstuckon spindle

I have a 653 have been soaking the rear wheel hubs with penetrating oil for 6 months still seem to be froze on the axles. A puller won't budge them,was thinking of heating them looking for suggestions.

I have a 653 have been soaking the rear wheel hubs with penetrating oil for 6 months still seem to be froze on the axles. A puller won't budge them,was thinking of heating them looking for suggestions.

How to remove astuck wheelbearing

@Russ VS do you have an old (spare) hub?You can make a puller out of an old hub using the 5 bolt holes and use a threaded rod for pushing on the axle.You will have more of an equal pull using the 5 bolt design.Someone on Red Square had some photos of this set-up...Maybe they will pust it again, otherwise, do a search on here for hub puller

Here is a OTC push puller and bearing separator tool kit. You can purchase it from places like tooltopia or thetoolwarehouse.net

so this is my homemade puller,it failed me on my newest tractor,c160 8 speed,it bent the 3/4 bolt,ya I had a 6 foot bar on it but it has removed many hubs before,just not the last one,something was gonna break

Wheelbearingstuckin knuckle

Receive a FREE 10" stainless steel skillet with the purchase of any of our electric or induction cooktops! ($50 value, no promo code necessary)

How to remove a rustedwheel hubbearing assembly

Try heating the area of the hub with a MAPP gas torch on the back side and use candle wax to wick between the hub and the axle. It may take a few times and applying pressure with a pressure puller and bearing separator to remove the hub.

I used a 3 leg puller after i soaked it for a day, then used a impact wrench which helped it absorb the pb blaster and it came right off!!

Wheel hub stuckon spindle

The key had worn out the hub and a previous owner filled the gap with epoxy, effectively glueing the hubs to the shafts.

I had the same problem when trying to have my tires changed on my D-160. I tried heat and every penetrating lubricant I had. That was when I thought to use my jack ( cylinder car or truck jack ), in a horizontal position. I used some wood blocks to position the jack, placed one end against the the hub I wanted off and used the opposing hub as a solid ground. It was so easy, I wished I had thought of it sooner.

I used a 3 leg puller after i soaked it for a day, then used a impact wrench which helped it absorb the pb blaster and it came right off!!

I tried the reverse hub method; but, it didn't work on a D-180 with the turning brake disc.  See pics. of stress crack in flange.  So... I have re-engineered my design to alleviate this via shifting the contact surface area {of the pullers inner plates} to the inner hub surface area as close to the axle as permissible, and the circumferential hex bolts outside of the hub.  No pics, as I have yet to remove any hubs with this puller design, since I am still waiting on some of the hardware to finish it.

Wheel Hubremoval tool

Russ, what kind of puller are you using? Marbletown, is that the one near Newark? if so, maybe we can get together and we can try my puller.

Russ, what kind of puller are you using? Marbletown, is that the one near Newark? if so, maybe we can get together and we can try my puller.

How to remove awheel hubwithout a puller

Russ, what kind of puller are you using? Marbletown, is that the one near Newark? if so, maybe we can get together and we can try my puller.

Try heating the area of the hub with a MAPP gas torch on the back side and use candle wax to wick between the hub and the axle. It may take a few times and applying pressure with a pressure puller and bearing separator to remove the hub.

How to get astuck wheel huboff

I just grabbed the tire and pulled mine off!  Hub and all!  Seems if the seal has been leaking for a long time it's easy!  Sorry, I'm serious but I'm sure you are too!  The tractor I just bought did just what I said but I'm sure yours is a "Bixxx"!  Certainly some PB Blaster or similar will help but you might need a HD puller!  There are examples of even custom made pullers that you could search for here, but most likely someone who has done it will be along shortly.Heat certainly helps!  Some smart raps with a large hammer on the side and a block of steel acting like an anvil on the opposite side does as well.  Also helps the solvent to penetrate!  Some have resorted to more extreme methods that sacrificed the hub but don't go there just yet!

Try heating the area of the hub with a MAPP gas torch on the back side and use candle wax to wick between the hub and the axle. It may take a few times and applying pressure with a pressure puller and bearing separator to remove the hub.

Russ, what kind of puller are you using? Marbletown, is that the one near Newark? if so, maybe we can get together and we can try my puller.

No I'm down in the Catskills exit 19 on the thruway, been up to the other Marbletown many times. Became friends with Gary and Michele VerStraete he's the Chief of FD there.How thick is the steel on the puller and bolt size might just have to make one.