Wheel bearings can be of either ball or tapered roller type. The ball bearings used for front wheel bearing applications are an angular type. An angular-type ball bearing will accept greater thrust loads than a Conrad-type bearing, which will accept a 100% load in the radial or thrust position and any combination of a 100% load. A tapered roller bearing will accept both a radial and a thrust load. All wheel bearings come in sets. The set consists of an inner and outer bearing.  As is the case of a rear axle that uses a “C” clip to retain the axle to the ring gear carrier.  The ring gear carrier bearings handle the thrust load and the straight roller at the flange end carries the radial load. Related Articles - TPMS: The silent guardian of tires - The importance of keeping up with the latest TPMS technology - Essential tips for becoming master of your wheel weight domain Some rear axles will have a cartridge-type wheel bearing set containing either ball or tapered roller set. SealsBasic seal construction remains the same, consisting of a metal retainer and seal. The primary sealing materials have changed from felt to rubber products, ranging from Buna N to Fluoroelastomers, yet felt is still used as a dust shield for the primary seal. A seal is only as good as the surface it rides on. A seal needs the surface it rides on to be lubricated. If the seal lip runs on a dry surface, it will over heat and become brittle. A scratch or gouge can damage the sealing lip and cause the seal to fail. It is very important that the seal be lubricated before it is installed to prevent it from running dry. A small amount of grease on the back of the seal and a film on the spindle is recommended. Don’t force it by getting a bigger hammer. It is highly recommended that a seal installer be used. The installer will prevent the seal from being cocked when it is installed. A shaft protector should be used when installing a seal over a splined shaft. The dust cap is also a vital part of the sealing system. A little extra care and a brass drift can make the job a lot easier. Some OEMs are setting new specifications for sealing and drag on some new vehicles. A tight seal and fuel efficiency do not go hand in hand. To meet the OEMs goals, some seal and bearing manufacturers are changing designs and materials in an effort to improve the overall performance of a bearing. Wheel Bearing AdjustmentA wheel bearing out of adjustment can reduce bearing life and can affect more than just the bearing. It affects the operation and service life of the spindle, wheel seal and brake components. It is important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. In fact, a recent survey showed that more than half of the bearings on the road today are adjusted incorrectly. Bearing adjustment did not become critical to braking performance until the introduction of disc brakes. The caliper is mounted directly to the steering knuckle. If there was too much endplay, it would cause piston knock back in the caliper, resulting is in excessive pedal travel. The use of direct mount of the caliper is returning to use on high-performance vehicles.  The following procedure is one method for adjusting the endplay of a wheel bearing set. Tighten the adjusting nut while turning the rotor or drum.  When the effort to turn the rotor or drum increases, a preload is placed on bearing assembly and all raceway surfaces are in contact, providing no end play. Back off the nut one flat to allow insertion of the cotter key. The endplay can be checked with a dial indicator. Mount the indicator with a magnetic or mechanical base as close to the center of the hub as possible. The indicator tip is set on a smooth surface at the end of the spindle. Push the rotor back and set the indicator to zero. Then pull the rotor or drum out and read the dial indicator. Allow 0.004 inch (0.100milimeters)  ± 0.003 inch (0.076 milimeters) endplay. Then lock the nut with a new cotter pin. Whether you are checking a conventional wheel bearing or hub bearing, the best tool for checking adjustment is a dial indicator. Many four-wheel-drive vehicles and most trucks with a load rating of one ton and higher, use a full floating axle. The axle has a bearing set, spindle and hub. The same adjustment procedure can be used for these applications.  Overtightening adjustable tapered roller bearings is a common error that can lead to premature failure. Tapered roller bearings on the front of RWD vehicles are never preloaded. They’re snugged up with no more than 15 to 20 foot- pounds of torque while rotating the wheel to make sure the bearings are seated. Then the adjustment nut is loosened 1/6 to 1/4 turn, and locked in place with a new cotter pin. As a rule, endplay should be about 0.001 to 0.005 inches. There should be no play on most FWD cars, but up to 0.010 inch of play in the front bearings may be acceptable on RWD vehicles. On FWD cars with adjustable tapered roller rear wheel bearings, the bearing adjustment procedure is usually the same as with RWD vehicles (zero pre-load), but some do require a slight pre-load. Ford, for example, says the rear wheel bearings on older Taurus models should be lightly preloaded to 24 to 28 inch- pounds (2 foot-pounds). Hub BearingsIn the late 1970s, the hub bearing began to appear on front-wheel-drive vehicles. This was a sealed, lubricated for life, pre-adjusted bearing with a mounting flange attached to the strut knuckle or rear axle flange and a hub for the rotor, wheel and CV joint. Other versions consist of a hub and bearing set that mount on a rear axle spindle or steering knuckle. The bearing could be either ball or roller type. Passenger car and light truck hub bearings are not adjustable. The hub is directly affected by the condition of the bearing. The driver may first notice a noise coming from the wheel of the vehicle when the steering wheel is turned. There will be noticeable endplay when the wheel is unloaded. A check using a dial indicator will show an endplay greater than 0.004 inch (0.100milimeters).  Bearing endplay can also affect a wheel speed sensor and cause an intermittent ABS trouble code. If the bearing flange has a runout, that runout will be magnified at the rotor friction surface. A runout of 0.0005 inch (0.00254mm) at the bearing flange could result in a 0.001 inch (0.0025milimeters) runout at the rotor friction surface. A wheel bearing is the most critical component of a braking system.  It positions the wheel and rotor to the caliper, the wheel and drum to the backing plate, and controls the input to the wheel speed sensor.  As Electronic Stability Control (ESC) braking systems become more complex, the wheel bearing will still be the central component to the system’s operation. With the introduction of the Electronic Wedge Brake (EWB) just around the corner the caliper, wheel speed sensor and chassis controller will become the ABS system. These changes will require greater care in the servicing of the total suspension system. ToolsTo avoid damaging the new bearing, the bearing inner race must be carefully pressed onto a shaft and the outer race pressed into its bore. Hammering a bearing in place can result in the rollers or balls dimpling the bearing races and causing premature failure. Most bearings have about 0.001 inch of interference-fit built into an axle shaft or bearing bore, which means that these types of bearings must be pressed or driven into place. Tapered bearing cups or outer races should be driven in place using a special aluminum driver. In an emergency, an old bearing race cut through on one side with an air-powered “whiz wheel” will serve the purpose. Special tools are also available for pressing bearings into a steering knuckle. Installation of bearings into an aluminum steering knuckle or housing can be expedited by using an electric hot air gun to gradually expand the housing without melting or distorting the metal. Lastly, always adjust a tapered roller bearing by torqueing to 15-20 foot-pounds. and spinning the hub to center the rollers in the races. Back this initial adjustment off a 1/8 or 1/4 turn and retorque the bearing to manufacturers’ specifications. A typical final torque of 20-30 inch-pounds will leave zero endplay and a slight amount of preload on the wheel bearing assembly. Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Frontwheel bearing purpose

Special tools are also available for pressing bearings into a steering knuckle. Installation of bearings into an aluminum steering knuckle or housing can be expedited by using an electric hot air gun to gradually expand the housing without melting or distorting the metal. Lastly, always adjust a tapered roller bearing by torqueing to 15-20 foot-pounds. and spinning the hub to center the rollers in the races. Back this initial adjustment off a 1/8 or 1/4 turn and retorque the bearing to manufacturers’ specifications. A typical final torque of 20-30 inch-pounds will leave zero endplay and a slight amount of preload on the wheel bearing assembly. Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Hub BearingsIn the late 1970s, the hub bearing began to appear on front-wheel-drive vehicles. This was a sealed, lubricated for life, pre-adjusted bearing with a mounting flange attached to the strut knuckle or rear axle flange and a hub for the rotor, wheel and CV joint. Other versions consist of a hub and bearing set that mount on a rear axle spindle or steering knuckle. The bearing could be either ball or roller type. Passenger car and light truck hub bearings are not adjustable. The hub is directly affected by the condition of the bearing. The driver may first notice a noise coming from the wheel of the vehicle when the steering wheel is turned. There will be noticeable endplay when the wheel is unloaded. A check using a dial indicator will show an endplay greater than 0.004 inch (0.100milimeters).  Bearing endplay can also affect a wheel speed sensor and cause an intermittent ABS trouble code. If the bearing flange has a runout, that runout will be magnified at the rotor friction surface. A runout of 0.0005 inch (0.00254mm) at the bearing flange could result in a 0.001 inch (0.0025milimeters) runout at the rotor friction surface. A wheel bearing is the most critical component of a braking system.  It positions the wheel and rotor to the caliper, the wheel and drum to the backing plate, and controls the input to the wheel speed sensor.  As Electronic Stability Control (ESC) braking systems become more complex, the wheel bearing will still be the central component to the system’s operation. With the introduction of the Electronic Wedge Brake (EWB) just around the corner the caliper, wheel speed sensor and chassis controller will become the ABS system. These changes will require greater care in the servicing of the total suspension system. ToolsTo avoid damaging the new bearing, the bearing inner race must be carefully pressed onto a shaft and the outer race pressed into its bore. Hammering a bearing in place can result in the rollers or balls dimpling the bearing races and causing premature failure. Most bearings have about 0.001 inch of interference-fit built into an axle shaft or bearing bore, which means that these types of bearings must be pressed or driven into place. Tapered bearing cups or outer races should be driven in place using a special aluminum driver. In an emergency, an old bearing race cut through on one side with an air-powered “whiz wheel” will serve the purpose. Special tools are also available for pressing bearings into a steering knuckle. Installation of bearings into an aluminum steering knuckle or housing can be expedited by using an electric hot air gun to gradually expand the housing without melting or distorting the metal. Lastly, always adjust a tapered roller bearing by torqueing to 15-20 foot-pounds. and spinning the hub to center the rollers in the races. Back this initial adjustment off a 1/8 or 1/4 turn and retorque the bearing to manufacturers’ specifications. A typical final torque of 20-30 inch-pounds will leave zero endplay and a slight amount of preload on the wheel bearing assembly. Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Wheel bearing purposeexplained

The following question is of the type "How much X percent of W", where W is the whole amount and X is the percentage figure or rate".

How to tell whichwheel bearingis bad while driving

Some OEMs are setting new specifications for sealing and drag on some new vehicles. A tight seal and fuel efficiency do not go hand in hand. To meet the OEMs goals, some seal and bearing manufacturers are changing designs and materials in an effort to improve the overall performance of a bearing.

Wheel Bearing AdjustmentA wheel bearing out of adjustment can reduce bearing life and can affect more than just the bearing. It affects the operation and service life of the spindle, wheel seal and brake components. It is important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. In fact, a recent survey showed that more than half of the bearings on the road today are adjusted incorrectly. Bearing adjustment did not become critical to braking performance until the introduction of disc brakes. The caliper is mounted directly to the steering knuckle. If there was too much endplay, it would cause piston knock back in the caliper, resulting is in excessive pedal travel. The use of direct mount of the caliper is returning to use on high-performance vehicles.  The following procedure is one method for adjusting the endplay of a wheel bearing set. Tighten the adjusting nut while turning the rotor or drum.  When the effort to turn the rotor or drum increases, a preload is placed on bearing assembly and all raceway surfaces are in contact, providing no end play. Back off the nut one flat to allow insertion of the cotter key. The endplay can be checked with a dial indicator. Mount the indicator with a magnetic or mechanical base as close to the center of the hub as possible. The indicator tip is set on a smooth surface at the end of the spindle. Push the rotor back and set the indicator to zero. Then pull the rotor or drum out and read the dial indicator.

While TPMS has been mandated for passenger vehicles in the U.S. and other countries, motorcycles are not yet a part of this legislation.

Average life ofwheelbearings

A wheel bearing is the most critical component of a braking system.  It positions the wheel and rotor to the caliper, the wheel and drum to the backing plate, and controls the input to the wheel speed sensor.  As Electronic Stability Control (ESC) braking systems become more complex, the wheel bearing will still be the central component to the system’s operation. With the introduction of the Electronic Wedge Brake (EWB) just around the corner the caliper, wheel speed sensor and chassis controller will become the ABS system. These changes will require greater care in the servicing of the total suspension system. ToolsTo avoid damaging the new bearing, the bearing inner race must be carefully pressed onto a shaft and the outer race pressed into its bore. Hammering a bearing in place can result in the rollers or balls dimpling the bearing races and causing premature failure. Most bearings have about 0.001 inch of interference-fit built into an axle shaft or bearing bore, which means that these types of bearings must be pressed or driven into place. Tapered bearing cups or outer races should be driven in place using a special aluminum driver. In an emergency, an old bearing race cut through on one side with an air-powered “whiz wheel” will serve the purpose. Special tools are also available for pressing bearings into a steering knuckle. Installation of bearings into an aluminum steering knuckle or housing can be expedited by using an electric hot air gun to gradually expand the housing without melting or distorting the metal. Lastly, always adjust a tapered roller bearing by torqueing to 15-20 foot-pounds. and spinning the hub to center the rollers in the races. Back this initial adjustment off a 1/8 or 1/4 turn and retorque the bearing to manufacturers’ specifications. A typical final torque of 20-30 inch-pounds will leave zero endplay and a slight amount of preload on the wheel bearing assembly. Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Allow 0.004 inch (0.100milimeters)  ± 0.003 inch (0.076 milimeters) endplay. Then lock the nut with a new cotter pin. Whether you are checking a conventional wheel bearing or hub bearing, the best tool for checking adjustment is a dial indicator. Many four-wheel-drive vehicles and most trucks with a load rating of one ton and higher, use a full floating axle. The axle has a bearing set, spindle and hub. The same adjustment procedure can be used for these applications.  Overtightening adjustable tapered roller bearings is a common error that can lead to premature failure. Tapered roller bearings on the front of RWD vehicles are never preloaded. They’re snugged up with no more than 15 to 20 foot- pounds of torque while rotating the wheel to make sure the bearings are seated. Then the adjustment nut is loosened 1/6 to 1/4 turn, and locked in place with a new cotter pin. As a rule, endplay should be about 0.001 to 0.005 inches. There should be no play on most FWD cars, but up to 0.010 inch of play in the front bearings may be acceptable on RWD vehicles. On FWD cars with adjustable tapered roller rear wheel bearings, the bearing adjustment procedure is usually the same as with RWD vehicles (zero pre-load), but some do require a slight pre-load. Ford, for example, says the rear wheel bearings on older Taurus models should be lightly preloaded to 24 to 28 inch- pounds (2 foot-pounds). Hub BearingsIn the late 1970s, the hub bearing began to appear on front-wheel-drive vehicles. This was a sealed, lubricated for life, pre-adjusted bearing with a mounting flange attached to the strut knuckle or rear axle flange and a hub for the rotor, wheel and CV joint. Other versions consist of a hub and bearing set that mount on a rear axle spindle or steering knuckle. The bearing could be either ball or roller type. Passenger car and light truck hub bearings are not adjustable. The hub is directly affected by the condition of the bearing. The driver may first notice a noise coming from the wheel of the vehicle when the steering wheel is turned. There will be noticeable endplay when the wheel is unloaded. A check using a dial indicator will show an endplay greater than 0.004 inch (0.100milimeters).  Bearing endplay can also affect a wheel speed sensor and cause an intermittent ABS trouble code. If the bearing flange has a runout, that runout will be magnified at the rotor friction surface. A runout of 0.0005 inch (0.00254mm) at the bearing flange could result in a 0.001 inch (0.0025milimeters) runout at the rotor friction surface. A wheel bearing is the most critical component of a braking system.  It positions the wheel and rotor to the caliper, the wheel and drum to the backing plate, and controls the input to the wheel speed sensor.  As Electronic Stability Control (ESC) braking systems become more complex, the wheel bearing will still be the central component to the system’s operation. With the introduction of the Electronic Wedge Brake (EWB) just around the corner the caliper, wheel speed sensor and chassis controller will become the ABS system. These changes will require greater care in the servicing of the total suspension system. ToolsTo avoid damaging the new bearing, the bearing inner race must be carefully pressed onto a shaft and the outer race pressed into its bore. Hammering a bearing in place can result in the rollers or balls dimpling the bearing races and causing premature failure. Most bearings have about 0.001 inch of interference-fit built into an axle shaft or bearing bore, which means that these types of bearings must be pressed or driven into place. Tapered bearing cups or outer races should be driven in place using a special aluminum driver. In an emergency, an old bearing race cut through on one side with an air-powered “whiz wheel” will serve the purpose. Special tools are also available for pressing bearings into a steering knuckle. Installation of bearings into an aluminum steering knuckle or housing can be expedited by using an electric hot air gun to gradually expand the housing without melting or distorting the metal. Lastly, always adjust a tapered roller bearing by torqueing to 15-20 foot-pounds. and spinning the hub to center the rollers in the races. Back this initial adjustment off a 1/8 or 1/4 turn and retorque the bearing to manufacturers’ specifications. A typical final torque of 20-30 inch-pounds will leave zero endplay and a slight amount of preload on the wheel bearing assembly. Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Badwheel bearingsymptoms

Most bearings have about 0.001 inch of interference-fit built into an axle shaft or bearing bore, which means that these types of bearings must be pressed or driven into place. Tapered bearing cups or outer races should be driven in place using a special aluminum driver. In an emergency, an old bearing race cut through on one side with an air-powered “whiz wheel” will serve the purpose.

Wheel bearingreplacement cost

As a rule, endplay should be about 0.001 to 0.005 inches. There should be no play on most FWD cars, but up to 0.010 inch of play in the front bearings may be acceptable on RWD vehicles.

Wheel bearingnoise

The hub is directly affected by the condition of the bearing. The driver may first notice a noise coming from the wheel of the vehicle when the steering wheel is turned. There will be noticeable endplay when the wheel is unloaded. A check using a dial indicator will show an endplay greater than 0.004 inch (0.100milimeters).  Bearing endplay can also affect a wheel speed sensor and cause an intermittent ABS trouble code. If the bearing flange has a runout, that runout will be magnified at the rotor friction surface. A runout of 0.0005 inch (0.00254mm) at the bearing flange could result in a 0.001 inch (0.0025milimeters) runout at the rotor friction surface.

TPMS hasn’t changed much since it was mandated in 2007, but Bluetooth sensors could be a welcome update for drivers and shops.

"To find the portion or the part from the whole amount, multiply the whole by the percentage, then divide the result by 100".

TPMS technology hasn’t changed much over the years. You might think, “But that’s a good thing, right? Don’t we want a consistent technology that can be fixed easily?” You may be on to something there, but TPMS technology currently relies on radio waves to transmit data. That means the radio spectrum the sensors use can be “noisy” with other nearby devices potentially causing interference with the sensor. It’s like someone interrupting you mid-sentence. Bluetooth sensors may be the answer to these radio-wave issues.

In the following example, consider that: The percentage figure is represented by X% The whole amount is represented by W The portion amount or part is represented by P Solution Steps The following question is of the type "How much X percent of W", where W is the whole amount and X is the percentage figure or rate". Let's say that you need to find 80 percent of 500. What are the steps? Step 1: First determine the value of the whole amount. We assume that the whole amount is 500. Step 2: Determine the percentage, which is 80. Step 3: Convert the percentage 80% to its decimal form by dividing 80 by 100 to get the decimal number 0.8: 80100 = 0.8 Notice that dividing by 100 is the same as moving the decimal point two places to the left. 80.0 → 8.00 → 0.80 Step 4: Finally, find the portion by multiplying the decimal form found in the previous step by the whole amount: 0.8 x 500 = 400 (answer). The steps above are expressed by the formula: P = W × X%100 This formula says that:"To find the portion or the part from the whole amount, multiply the whole by the percentage, then divide the result by 100". The symbol % means the percentage expressed in a fraction or multiple of one hundred. Replacing these values in the formula, we get: P = 500 × 80100 = 500 × 0.8 = 400 (answer) Therefore, the answer is 400 is that 80 percent of 500.

Frontwheel bearingnoise symptoms

Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

Overtightening adjustable tapered roller bearings is a common error that can lead to premature failure. Tapered roller bearings on the front of RWD vehicles are never preloaded. They’re snugged up with no more than 15 to 20 foot- pounds of torque while rotating the wheel to make sure the bearings are seated. Then the adjustment nut is loosened 1/6 to 1/4 turn, and locked in place with a new cotter pin.

One way of visualizing 80 percent is through a pie chart. In this example, the orange slice represents the percentage of the whole pie.

Tire changing is a straightforward procedure for most technicians, but the transition from ICE vehicles to EVs will introduce some changes.

ToolsTo avoid damaging the new bearing, the bearing inner race must be carefully pressed onto a shaft and the outer race pressed into its bore. Hammering a bearing in place can result in the rollers or balls dimpling the bearing races and causing premature failure.

SealsBasic seal construction remains the same, consisting of a metal retainer and seal. The primary sealing materials have changed from felt to rubber products, ranging from Buna N to Fluoroelastomers, yet felt is still used as a dust shield for the primary seal. A seal is only as good as the surface it rides on. A seal needs the surface it rides on to be lubricated. If the seal lip runs on a dry surface, it will over heat and become brittle. A scratch or gouge can damage the sealing lip and cause the seal to fail. It is very important that the seal be lubricated before it is installed to prevent it from running dry. A small amount of grease on the back of the seal and a film on the spindle is recommended. Don’t force it by getting a bigger hammer. It is highly recommended that a seal installer be used. The installer will prevent the seal from being cocked when it is installed. A shaft protector should be used when installing a seal over a splined shaft. The dust cap is also a vital part of the sealing system. A little extra care and a brass drift can make the job a lot easier. Some OEMs are setting new specifications for sealing and drag on some new vehicles. A tight seal and fuel efficiency do not go hand in hand. To meet the OEMs goals, some seal and bearing manufacturers are changing designs and materials in an effort to improve the overall performance of a bearing. Wheel Bearing AdjustmentA wheel bearing out of adjustment can reduce bearing life and can affect more than just the bearing. It affects the operation and service life of the spindle, wheel seal and brake components. It is important to adjust the wheel bearing endplay to the proper specifications. If the bearing set is adjusted too loose or too tight, it can cause the bearing to fail prematurely. In fact, a recent survey showed that more than half of the bearings on the road today are adjusted incorrectly. Bearing adjustment did not become critical to braking performance until the introduction of disc brakes. The caliper is mounted directly to the steering knuckle. If there was too much endplay, it would cause piston knock back in the caliper, resulting is in excessive pedal travel. The use of direct mount of the caliper is returning to use on high-performance vehicles.  The following procedure is one method for adjusting the endplay of a wheel bearing set. Tighten the adjusting nut while turning the rotor or drum.  When the effort to turn the rotor or drum increases, a preload is placed on bearing assembly and all raceway surfaces are in contact, providing no end play. Back off the nut one flat to allow insertion of the cotter key. The endplay can be checked with a dial indicator. Mount the indicator with a magnetic or mechanical base as close to the center of the hub as possible. The indicator tip is set on a smooth surface at the end of the spindle. Push the rotor back and set the indicator to zero. Then pull the rotor or drum out and read the dial indicator. Allow 0.004 inch (0.100milimeters)  ± 0.003 inch (0.076 milimeters) endplay. Then lock the nut with a new cotter pin. Whether you are checking a conventional wheel bearing or hub bearing, the best tool for checking adjustment is a dial indicator. Many four-wheel-drive vehicles and most trucks with a load rating of one ton and higher, use a full floating axle. The axle has a bearing set, spindle and hub. The same adjustment procedure can be used for these applications.  Overtightening adjustable tapered roller bearings is a common error that can lead to premature failure. Tapered roller bearings on the front of RWD vehicles are never preloaded. They’re snugged up with no more than 15 to 20 foot- pounds of torque while rotating the wheel to make sure the bearings are seated. Then the adjustment nut is loosened 1/6 to 1/4 turn, and locked in place with a new cotter pin. As a rule, endplay should be about 0.001 to 0.005 inches. There should be no play on most FWD cars, but up to 0.010 inch of play in the front bearings may be acceptable on RWD vehicles. On FWD cars with adjustable tapered roller rear wheel bearings, the bearing adjustment procedure is usually the same as with RWD vehicles (zero pre-load), but some do require a slight pre-load. Ford, for example, says the rear wheel bearings on older Taurus models should be lightly preloaded to 24 to 28 inch- pounds (2 foot-pounds). Hub BearingsIn the late 1970s, the hub bearing began to appear on front-wheel-drive vehicles. This was a sealed, lubricated for life, pre-adjusted bearing with a mounting flange attached to the strut knuckle or rear axle flange and a hub for the rotor, wheel and CV joint. Other versions consist of a hub and bearing set that mount on a rear axle spindle or steering knuckle. The bearing could be either ball or roller type. Passenger car and light truck hub bearings are not adjustable. The hub is directly affected by the condition of the bearing. The driver may first notice a noise coming from the wheel of the vehicle when the steering wheel is turned. There will be noticeable endplay when the wheel is unloaded. A check using a dial indicator will show an endplay greater than 0.004 inch (0.100milimeters).  Bearing endplay can also affect a wheel speed sensor and cause an intermittent ABS trouble code. If the bearing flange has a runout, that runout will be magnified at the rotor friction surface. A runout of 0.0005 inch (0.00254mm) at the bearing flange could result in a 0.001 inch (0.0025milimeters) runout at the rotor friction surface. A wheel bearing is the most critical component of a braking system.  It positions the wheel and rotor to the caliper, the wheel and drum to the backing plate, and controls the input to the wheel speed sensor.  As Electronic Stability Control (ESC) braking systems become more complex, the wheel bearing will still be the central component to the system’s operation. With the introduction of the Electronic Wedge Brake (EWB) just around the corner the caliper, wheel speed sensor and chassis controller will become the ABS system. These changes will require greater care in the servicing of the total suspension system. ToolsTo avoid damaging the new bearing, the bearing inner race must be carefully pressed onto a shaft and the outer race pressed into its bore. Hammering a bearing in place can result in the rollers or balls dimpling the bearing races and causing premature failure. Most bearings have about 0.001 inch of interference-fit built into an axle shaft or bearing bore, which means that these types of bearings must be pressed or driven into place. Tapered bearing cups or outer races should be driven in place using a special aluminum driver. In an emergency, an old bearing race cut through on one side with an air-powered “whiz wheel” will serve the purpose. Special tools are also available for pressing bearings into a steering knuckle. Installation of bearings into an aluminum steering knuckle or housing can be expedited by using an electric hot air gun to gradually expand the housing without melting or distorting the metal. Lastly, always adjust a tapered roller bearing by torqueing to 15-20 foot-pounds. and spinning the hub to center the rollers in the races. Back this initial adjustment off a 1/8 or 1/4 turn and retorque the bearing to manufacturers’ specifications. A typical final torque of 20-30 inch-pounds will leave zero endplay and a slight amount of preload on the wheel bearing assembly. Whether installing a ball, roller or sealed bearing assembly, using correct procedures and tools will ensure a comeback-free wheel bearing installation.

On FWD cars with adjustable tapered roller rear wheel bearings, the bearing adjustment procedure is usually the same as with RWD vehicles (zero pre-load), but some do require a slight pre-load. Ford, for example, says the rear wheel bearings on older Taurus models should be lightly preloaded to 24 to 28 inch- pounds (2 foot-pounds).

Another way of visualizing percentages is using a bar chart like the one below. The orange bar represents 80, percent and the full square represents the whole or 100%.