For high precision applications, such as a belt & pulley system, where high response and quick positioning after load changes are needed without adjusting any gains or required tuning of the motor, Oriental Motor offers a wide range of stepper motor and tuning-free servo motors.

ElectricMotorBelts near me

2. RS-485 / Modbus (RTU) - Operating data and parameters can be set and operation commands can be input using RS-485 communication. Up to 31 drivers can be connected to each serial communication module. Also there is a function that enables the simultaneous start of multiple axes. The protocol supports Modbus (RTU), enable connection with devices such as a touch screen (HMI) or PCs.

Let your local Meineke Car Care Center perform a diagnosis and we’ll let you know how we can repair or replace your wheel bearings to get your car back to a healthy state.

For conveyors that require higher accuracy positioning Oriental Motor offers a wide range of Stepper Motor and Servo Motor solutions. Stepper motors, with their ability to product high torque at a low speed while minimizing vibration, are ideal for applications requiring quick positioning over a short distance. Servo motors are easy to operate and allow for smooth operation with large inertial loads and belt mechanisms. Servo motors are ideal for positioning over long distances using a flat torque characteristic from low to high speeds.

Upon completing the service, the technician will take your vehicle for a test drive to check the noise levels and ride quality. If all goes well, you will then have your vehicle returned to you.

After placing the hub in the press, it takes several minutes to change the wheel bearings. Your new bearings must also be pressed into the hub to seat their rear surface at the correct point.

At this point, you must have a qualified technician change out the worn components using a wheel bearing press to restore your vehicle to good working condition and eliminate distressing noises and poor ride quality.

Belt driveMotorPulley

In many cases, the diagnostic process will quickly pinpoint the front wheel bearings as the cause. Upon confirming the diagnosis, a technician will write up a work order that includes the total cost to replace your wheel bearings.

Oriental Motor offers Network products under the FLEX concept, meaning each product is equipped with an interface that connects to various master controllers featuring I/O, RS-485 / Modbus (RTU) or Factory Automation. Networked products enable operating data and parameters for each motor to be set at a Master Controller and sent to each driver. In addition, operation commands can be input send set using various communication methods to meet the need of a wide range of available Network Solutions.

At first, bad wheel bearings will start to squeak loudly while you drive. You will know it is time to replace the wheel bearing if the noise is constant, not just when you press the brakes.

In order to understand the big picture and repair your vehicle properly, technicians must check wear on a variety of components from tires and brakes to tie rods and control arms to find the source of the noise and vibrations.

V-belt

Geared stepper motors not only achieve deceleration, high torque and high resolution, but they are capable of driving larger inertial loads compared to a standard motor.

The communication protocol of the master controller, Factory Automation (FA) network, is converted to Oriental Motor's own RS-485 communication protocol. Connection to FLEX-compatible products is completed with one RS-485 communication cable.

A wide range of gearing options are available to provide higher permissible inertia, higher resolution positioning and higher torque for index table and high inertia applications.

MotorBelt price

Your vehicle utilizes a wheel bearing at the hub to allow the tire and rim to smoothly rotate at both low and high speeds. As a rotating part, the wheel bearing's material slowly wears down during usage.

The servo motor has restrictions on permissible load inertia, but the geared type can be used to greatly increase the load size that can be driven.

ElectricmotorBelt

Technicians receive ample training to learn how to change wheel bearings correctly. Technicians use heavy-duty tools in the shop, including a large press, to pop the bearings out of the hub. On most vehicles, your technician must remove the tire, rotor and hub to access the bearing mounting point.

Stepper Motors are suitable for high accuracy positioning over a short distance and provide high torque even at low speeds. Stepper motors also offer very low vibration and a wide range of features and options such as gearheads, encoders and built-in controllers to meet the specific needs of your application.

Any time your vehicle is making unusually loud noises it’s safe to assume that something’s not right. Sometimes the culprit is your car’s wheel bearings. Wheel bearing press service, bearings replacement or other services may be required. Read below to learn about symptoms of problematic wheel bearings and replacement services.

Motorbelt replacement

For system solutions requiring connection to an upper level controller, PLC or HMI, Oriental Motor offers several networked products to allow for easy control using I/O or RS-485 / Modbus (RTU) networks.

Servo Motors provide accurate positioning for quick moves or for a long distance moves. All feature a closed loop configuration ideal for variable loads and offer a wide range of gear options and braking or load holding options. The built-in controller (stored data) FLEX also helps for system configuration considerations.

3. Factory Automation Network - Use of a network converter (sold separately) enables support with CC-Link, MECHATROLINK or EtherCAT communication. Operating data and parameters can be set and operation commands can be input using various communication methods.