Alexander Screw Products, Inc. (DBA AnchorBoltExpress.com)  can receive calls and  SMS messages. By calling or sending an SMS message you agree to receive a response to your request. Alexander Screw Products does not send out promotional or informational messages by SMS or telephone. While we do not send SMS for promotional reasons you may always reply STOP to end a conversation. If you have subscribed to our mailing list by email you may receive email marketing, which includes a link at the bottom to unsubscribe.

This material meets the A193 Grade B7 specification. B7 is a heat-treated alloy steel that has been quenched and tempered.Rods can easily be cut to length in the field with a hacksaw or band saw.Tensile Strength: 125 (ksi, min)Yield: 105 (ksi, min)

This useful tool will tell you the center distance between pulleys, or if you want a certain center distance, it will tell you what belt size you need.

Dropped my car off at a mechanic to check into an issue I’ve been having (groaning in the front/left wheel). Turns out it is a wheel bearing that needs to be replaced and the mechanic quoted me $750 for the job, saying “the bearing needs to be pressed and it’s a fair amount of labor”.

Elantra has same bearing setup as Honda’s. A shop can lowball the cost and then have to replace more parts or remove knuckle to press out bearing. The bearing is pressed into the hub. So, assume the hub will be damaged or scored.image600×600 22.3 KB

They need to be tight due to the super tight tolerance on positioning for proper operation. I did some work recently and had to R&R an ABS sensor. Long story short, a thousandth made a huge difference in signal level. Too close and it rubs, too far and weak signal. Rust forming on the spacer was enough to cause weak signal…removing them required diligent care not to damage them…

Cool. With that said, you really should consider getting the other one replaced at the same time…see if the shop will give you a break on the labor.

I took my knuckle to a shop and they pressed out my bearing and he said hub was scored but he had 1 used. For $20. I tried to pay with my card and tech said hub was his and cash only. Had to run to atm for $20 cash. Bet tech had a few hubs in his toolbox. From other jobs?

You should also verify how many wheel bearings they’re replacing. If it were me, I would go ahead and replace the bearing on the other side of the vehicle as well…chances are, it’s not far behind in terms of failure.

This doesn’t include the cost of replacing one perfectly good ABS sensor that had to be destroyed in the process. (tech told me that the sensor would be in the way of the press, and they couldn’t remove it without destroying it. ). I believed him, as I replaced the ABS sensor on the other side a year earlier. It was defective. I too had to destroy the old one to remove it, as Toyota machined the hole too small. Talk about a tight fit! There was TSB about this, I believe.

I paid $250 parts and labor for the front wheel bearing of my previous Toyota Corolla. It had to be pressed in also. They put in a Timken bearing and it didn’t take much time…around 45 minutes and I was out of there.Shop around because your estimate seems on the high side.

How many millimeters in -2.025 inches? -2.025 inches is equal to -51.435 millimeters. ... -2.125 inch = -53.975 mm. -2.025 inch, -2.025 inch = -51.435 mm. -1.025 ...

2006-2011 Honda Civic Wheel Bearing and Hub Assembly 10012079.

I thought sometimes they just replace the whole hub part is a little more but less labor. That price sounds high you need to get a second quote.

Yeah, tight but not pressed in I had to pry mine out a fraction at a time, going around to keep it from getting jammed. Both GM and an 03 Toyota Camry. The GM had a penta-socket head fastener on one side and a pressed in “rivet” on the other. Still struggling to understand/justify the need for such hardware…

A193B7

You did the right thing by getting other quotes and as an aside, never give a lot of credence to online reviews. Some may be fake and in some cases people may have been robbed blind and simply do not realize it. Their car is fixed for double what anyone else charges so they’re happy with it all.

Same with a guy I know in my area who passed away back in 2011. He BSed, cobbled together, hacked up, and in general screwed everyone over yet everyone within 25 miles of him praised his name to the mechanical heavens. Go figure…

After I drilled out the defective sensor , I took a reamer to the hole. The shop that removed the other sensor (left front) was nice enough to let me go home without a sensor (I got one from an online Toyota dealer at a big discount). And my labor is free.

Brake Bleeder Kit - Mityvac MV6830 Vacuum Brake Bleeder - MV6830.

Did you get an itemized estimate? If not, ask for one. Do that when you get a second opinion too. That way you can easily compare the two. Don’t tell the second shop what the other one estimated.

you can get the whole hub and bearing for like $150 , so your mechanic is telling you it is going to take him 5 hours to do the job on a bearing ?? I doubt it , i would run from that guy .

Scope of work as per the first shop was to “replace the left/front wheel bearing and press the new one”, that’s all they mentioned.

As always when in doubt you get a second opinion . It could be that this shop does not have the right equipment for the job or there is a lot of labor involved .

SKF offers a wide range of bearings and seals designed for automotive applications, ensuring optimal performance and reliability.

1/2-13" B7 Fully Threaded RodHardware: Each rod comes with 1 Heavy Hex Nut and 1 F436 Washer.Standard lengths are 6 inch, 12 inch, 18 inch, 24 inch, and 36 inch.Our rods are cut to length after order, for custom lengths not available online up to 6' contact us here.Perfect for general construction, maintenance, concrete, epoxy, or repairs.

The inner race was rusted and pitted – it looks like moisture found its way past the hub seal and compromised the race.

Thanks all, appreciate the help. I did call a second and third shop and was quoted $350 by one and $380 from the other. Both shops gave me their estimate, and when they then asked what I was quoted when it was diagnosed they said the shop I went to was notorious for extremely high prices and that $750 was way too high… I’m surprised since the first shop had great reviews.

29413-E1-XL Axial spherical roller bearing at Schaeffler medias ▻ View all product data here & buy online.

You didn’t mention the year of your Elantra, but when I plugged in a 2015 into repairpal.com for an estimate, my local zip code brought up an estimate for $173-266 to change a single wheel bearing…you definitely need to get a 2nd and 3rd quote

Browse Homes for Sale and the Latest Real Estate Listings in 51106.

ASTM A193

Not necessarily. I had this setup on my old Mazda Protege. You press the hub out of the bearing, and the inner race of the bearing is stuck in the hub. You then carefully score the outside of the inner race, and strike it once or twice with a chisel…the inner race splits in too, and you’re left with the hub, which you can press into the new bearing.

TRH thyrotropin releasing hormone [ (human)]. Gene ID: 7200, updated on 10-Dec-2024. Summary. This gene encodes a member of the thyrotropin-releasing ...

View22049-95-2)/(Methyl 2-oxopyrrolidine-3-carboxylate)information and documentation regarding (Methyl 2-oxopyrrolidine-3-carboxylate), including NMR, ...