Take the castellated nut, the spacer, and the dust cap, clean them, and put them somewhere where you won’t kick them across the garage floor.

Give the inside of the hub and the bearing races a quick cleaning with a paper towel so you can see what’s what. You should be able to see the smaller outer bearing race pressed into the front of the hub, and the larger inner race pressed into the back. If you look inside the hub from both sides, you should see two notches behind each race that allow you to bang them out. Using a hammer and the drift of your choice (e.g., an old screwdriver, a beat-up quarter-inch ratchet extension, or even an actual drift punch), and working on one race at a time, knock it out by banging alternately on the two notches. Then move on to the other race. It doesn’t matter which one you do first.

A Crowned Yoke Style cam follower is a type of roller bearing with a convex (crowned) outer surface that helps to reduce stress and evenly distribute load across the bearing surface. It is commonly used in applications where heavy loads and high-misalignment conditions are present, and helps to ensure consistent contact between the bearing and the cam or track it is following.

At this point, before I button things up, I like to test-fit the wheel, spin it, and check for play. If you do this, take care not to get any dirt into the open bearing (you can gently tap the bearing cap into place). The wheel should spin smoothly and quietly. Grab the wheel at 6 and 12 and push and pull it. There should be no play, or only a small hint of play.

Next, take a paper towel and clean the spindle. Inspect the two flat surfaces. The bearings themselves do not actually run on these surfaces. Instead, they serve as the seating surfaces for the rings in the center of the bearing assemblies. However, if these surfaces are badly pockmarked or gouged, the inner bearing rings may not sit firmly on them, allowing the entire bearing to wobble. If that is the case, and if, after replacing the bearings and adjusting them, there is still substantial play in the wheel, the entire strut housing may need to be replaced. Fortunately, this is extremely rare, and usually comes only from catastrophic bearing failure—which is why, when you feel play that can’t be adjusted out, you replace the bearings.

Flanged Concentric Stud Style Cam followers are a type of cam follower bearings that have a flange on one side and a stud on the other side. The stud provides a way to attach the bearing to a shaft or other mechanism, while the flange helps to locate and stabilize the bearing. These cam followers are typically used in applications where a high load capacity is needed, and where the bearing needs to be attached to a shaft or other mechanism.

A Plain Concentric Stud Style Cam Follower is a type of roller bearing that has a cylindrical stud as the inner raceway, with the outer raceway being a cylinder that is concentric with the stud. This design provides a simple and reliable solution for light to medium load applications where a low profile and minimal axial space are required. The stud allows for easy installation, and the plain (non-flanged) outer surface provides minimal axial height, making it suitable for applications with tight installation constraints.

Once you’ve packed the crevices, cram the outer circumference of the bearing into your palm, working the grease into the individual rollers. Be sure that it’s well packed. Remember: You’re likely giving this bearing the only lubrication it’ll receive for decades. When the bearing is well-packed, put it down on a new clean paper towel. Do this with both the inner and outer bearings.

Spray everything down with the cleaner of your choice and scour it thoroughly. Then, as you did with the spindle, inspect the surfaces that the races sat in; I’ve never seen one ruined, but it’s not uncommon to see some gouging from the races being banged in and out. If gouging in one area is pronounced, you can take off the high spots with some Scotch-Brite, but don’t go nuts and risk not having the race fit snugly.

Your challenge. Our solution. Osborn offers the best solutions for your mechanical surface treatment challenges. Our experts are highly trained to serve you with the optimum off-the-shelf or customized tools, when and where you need them. Unlike others, we help you optimize your process, meet the highest quality and safety requirements and reduce your costs.

Open the package with your nice new bearing. It should contain the bearing and the race. It doesn’t matter whether you select the inner or outer bearing first. Withdraw the race and set the bearing down on a clean paper towel or plastic sheet.

Next, you need to find the gap in the castellated nut that best lines up with the hole in the end of the spindle. The Internet is full of stories of people who burned out wheel bearings in a hundred miles by over-tightening them. I was always trained to tighten the nut by hand, then back it off to line it up with the hole, but a friend pointed out to me that the 2002 factory manual calls for the nut to be tight enough that the spacer can be moved by prying it with a screwdriver. Check your manual for the correct procedure.

The classic test is to jack up the front of the car, support it on stands, grab each wheel at 6 o’clock and 12 o’clock, and gently rock it. If you feel play, the wheel bearing needs to be adjusted. If you can’t adjust out the play, or if when you spin it you hear and feel noise, it’s time to replace the bearings.

With the inner bearing trapped in place by the seal, turn the hub over and coat the outer bearing race with grease. Clean any grease off the rotors.

Stainless steel eccentric stud flanged cam followers are bearings that consist of a cylindrical outer ring with a flange on one end, a central eccentric stud that allows for attaching other machine components and adjustability of the radial clearance between the cam and the follower, and a inner ring that rotates around the stud axis. They are made of stainless steel which is a type of steel that contains a minimum of 10.5% chromium, making it highly resistant to corrosion and rust. This makes them suitable for use in harsh environments where corrosion resistance is required. The eccentric design of the stud allows for adjustability which is useful when precise linear motion with adjustability is required.

If you are replacing the rotors, now is a good time to take the old ones off. On my 2002, they were held by four 8-mm Allen-head bolts, whereas on the Lotus, they were attached using traditional bolts. In either case, this is one of those times where owning an impact wrench makes it so easy that it’s almost not fair. If you don’t have one, you may need to clamp the old rotor in a vise to hold it still. Draw the bolts and their lock washers out, then separate the rotor from the hub. If it’s been on there for 40 years, you may need to persuade it with a few smacks from a hammer.

A Plain Eccentric Stud Style Cam Follower is a type of roller bearing that has a cylindrical stud as the inner raceway, with the outer raceway being a cylinder that is offset (eccentric) with the stud. This design provides a simple and reliable solution for light to medium load applications where the ability to compensate for misalignment or shaft deflection is required. The stud allows for easy installation, and the plain (non-flanged) outer surface provides minimal axial height, making it suitable for applications with tight installation constraints. The eccentricity of the outer raceway provides the ability to adjust for misalignment, making it suitable for use in applications with shaft deflection or other sources of misalignment.

Each of our products was originally developed as a specialty item to meet the requirements of specific client applications and their unique environments. Over time, the Osborn Load Runners product was made available to all industries but continues to be customized to meet the specific needs of our customers.

Finally, put the cotter pin through the notch and the hole, and bend it far enough that it won’t hit the bearing cap. Put some grease in the cap and tap it back into place.

When installing the bearings, order is important. You must drop the inner bearing in first, then install the bearing seal to trap it in place, then slide the entire hub assembly onto the spindle, then slide the outer bearing into place, and then trap it with the spacer and nut.

I recently needed to do brake and bearing work on both my Lotus Europa and on one of my BMW 2002s. The two repairs were nearly identical. I’ll show it for the BMW simply because the photographs came out better, and I’ll point out the handful of minor differences.

Next comes the fun part: Packing the bearings. There are few things more automotively primal, elemental, and intimate than packing bearings. Use whatever grease you’re comfortable with. Like with motor oil, many people swear by certain greases. I haven’t found that it matters. Traditional brown 100-percent petroleum-based grease, black semi-synthetic, or red 100-percent synthetic are all fine, as long as the package lists “automotive bearings” among the applications.

To remove the inner wheel bearing, you first need to pry the seal out of the back of the hub. You’re replacing it, so don’t worry about destroying it. A long screwdriver rocking on a fulcrum point like the handle of a hammer usually does the trick. With the seal out, withdraw the inner wheel bearing. Again, hold onto it for a bit in case you need to compare sizes.

High temp flanged style cam followers are bearings that are specifically designed for use in high temperature environments. They typically consist of a cylindrical outer ring with a flange on one end, and an inner ring that rotates around a central axis. The flange on the outer ring allows for easy installation. They are made of materials that can withstand high temperatures, and have special sealing and lubrication to prevent damage from high temperatures.

When the race is fully seated, you should hear the sound change from a ringing to more of a thud as you’re tapping it in, but you should also check by turning the hub over and carefully examining where the back of the race is visible through the slots. Be certain that there is no space behind the race. Then do the same thing with the other bearing race. You should now have both the inner and outer races seated.

Take the new race and place it in the hub. Square it up, then gently tap it in with a rubber hammer, or a hammer and wood block, or hammer and a hockey puck, then stop and look at it carefully to determine whether it’s going in cocked, which it almost always is. If it is badly cocked, it can gouge the mating surface, so you want to correct it as quickly as possible. Gently tap on the high side until it is going in level, then continue tapping until it’s flush with the top of the hub.

When the race is flush with the top of the hub, switch from a block of wood to using a socket whose diameter is just slightly smaller than the race. You’ll have to figure this out by trial and error, as the exact outer diameter varies socket to socket, but on the 2002, I used a 1-13/16-inch socket on the larger inner race and a 1-3/8-inch socket on the smaller outer race.

Rob Siegel has been writing the column The Hack Mechanic™ for BMW CCA Roundel magazine for 30 years. His most recent book, Just Needs a Recharge: The Hack Mechanic™ Guide to Vintage Air Conditioning, is available on Amazon (as are his previous books). You can also order personally inscribed copies here.

Slide the hub and rotor assembly onto the spindle, pressing it gently but firmly to get the inner bearing to seat on the spindle. Slide the outer bearing over the end of the spindle and into its race, then slide the spacer over the end of the spindle. Thread the castellated nut onto the end of the spindle. Be careful not to cross-thread it. Once the nut is on, spin it on as far as it will go by hand, then gently use a wrench on it, as both the inner and outer bearing rings sometimes need to seat on the spindle. It should be obvious when they’re seated. Do not apply any real torque on the nut. You’re not trying to tighten it.

Flanged crown concentric cam followers are a type of bearing that consist of a cylindrical outer ring with a flange on one end, and a cylindrical or crowned inner ring that rotates around a central axis. They are designed to follow the movement of a cam, which is a mechanical device that converts rotary motion into linear motion. The flange on the outer ring allows for easy installation, while the concentric design helps to maintain proper alignment and reduce wear on the bearing.

Companies who are seeking to improve efficiency and reduce the cost of heavy-duty load handling in a variety of applications can find a partner in Osborn Load Runners. Since 1887, we’ve been a leader in idler roller and cam follower innovation. More importantly, we’ve been a partner to dozens of industries to solve engineering and design problems in order to keep them up and running.

Sign up for the latest automotive news and videos—in short, everything for people who love cars

You begin by removing the caliper. If you’re also replacing the pads, it’s easiest if you first bang the pins out of the caliper before you unbolt it from the strut. Note that the original brake pads and shoes on a vintage car may contain asbestos, so wearing a dust mask is a wise precaution when dealing with brake components. Remove the bolts holding the caliper to the strut. There may also be a bolt holding the brake line bracket to the strut. Set the caliper on the control arm or hang it from the spring with a zip tie.

A Flanged Yoke Style Cam Follower is a type of roller bearing that has an outer flange or rim to increase the surface area and stability of the bearing. It is commonly used in high-load and high-misalignment applications, providing increased stability and accuracy for the cam or track it is following. The flange also helps to simplify the mounting process and provides additional support for the bearing.

Flanged eccentric stud style cam followers are bearings that consist of a cylindrical outer ring with a flange on one end and an inner ring that is attached to the stud shaft by an eccentric collar. This design allows for adjustability of the radial clearance between the cam and the follower. The flange on the outer ring allows for easy installation and the stud shaft can be used for attaching other machine components.

The front hub layout on many vintage cars is such that there are inner and outer bearings, each running in a race that’s pressed into the hub. The inner bearing is protected by a pressed-in seal, the outer bearing by a dust cap. The hub assembly—hub plus rotor plus bearings—slides onto a spindle that protrudes at a right angle from the strut, and it’s held in place by a castellated nut, so named because it has notches in it like the crenellations in the parapet of a castle or the top of a rook chess piece. One of the notches is lined up with a hole that’s drilled through the end of the spindle. A cotter pin is used to secure the nut.

Straighten out the cotter pin with needle-nosed pliers, remove it, and then unscrew the nut from the spindle. It shouldn’t be on tight, but if it is, a wrench can get it started. Withdraw the thick spacer that’s behind the nut.

And that’s it. Unless you own the car for 30 more years and drive the bejesus out of it, you’ll probably never have to change the front wheel bearings again.

Flanged crowned eccentric stud cam followers are a type of bearing that consist of a cylindrical outer ring with a flange on one end, and an inner ring that rotates around a central axis which is offset from the bearing center. They are designed to follow the movement of a cam, which is a mechanical device that converts rotary motion into linear motion. The flange on the outer ring allows for easy installation and the eccentric design allows for adjustability in the radial direction.

Wheel bearings generally live a long time on street cars, but front-wheel bearings suffer increased stress due to the steering, so they may need to be replaced at some point on a vintage car.

Stainless steel concentric stud flanged style cam followers are bearings that consist of a cylindrical outer ring with a flange on one end, a central concentric stud that allows for attaching other machine components and a inner ring that rotates around the stud axis. They are made of stainless steel which is highly resistant to corrosion and rust. This makes them suitable for use in harsh environments where corrosion resistance is required.

The next step is to slide the hub onto the spindle, but before that, there’s the question of whether the hub bore is supposed to be packed with grease. Consult a repair manual for the car. On the 2002, the grease packed into the bearings and dust cap were deemed enough, but on the Lotus, the manual said to pack the hub’s center bore approximately half full of grease.

Use a glob of grease to coat the inner bearing race, then set the inner bearing down inside it. Take the inner wheel-bearing seal and install it as you did the bearing races, tapping it into place and taking care not to cock it, but only get it flush with the inner surface of the hub. Don’t pound it in any farther than that. The BMW 2002 had the rubber grease seal shown, but the Lotus had an old-school felt seal where the felt was on the outside, greased, and meant to be in light contact with the base of the spindle. Care needed to be taken to test-fit the hub assembly to be certain the clearance of the felt seal was adequate.

Begin disassembling the hub by fishing the outer wheel bearing out. Don’t throw it away just yet, in case you need to compare it to the new bearing.

Next, pull the hub and rotor assembly forward and off the spindle, but be aware that the outer wheel bearing may slide out, so be prepared to catch it. Lay everything on a clean piece of cardboard or a paper towel.

Either wash your hands or use a pair of rubber gloves. I’d advise wearing a Tyvek suit, as you’re likely going to get grease on whatever you’re wearing. Take a good-sized glob of grease and put it in the palm of your hand. Then take the bearing and press it in the wad of grease in your palm, almost like you’re scooping ice cream with a spoon, and work the grease into every crevice around the rim of the bearing. Replenish the grease in your palm as necessary. Do this for both the front and back of the bearing.

A Plain Yoke Style Cam Follower is a type of roller bearing that has a plain (non-flanged) outer surface and a yoke-shaped inner ring. It is commonly used in light to medium load applications and provides a simple, low-cost solution for cam and track following. The yoke-shaped inner ring allows for easy installation and the plain outer surface provides minimal axial height, making it suitable for applications with tight installation constraints.

On many vintage cars, replacing front wheel bearings is synergistic with replacing the front rotors. This is because the front rotors are often behind the front hubs, which means that to change the rotors you have to pull the hubs off the front spindles, at which point the bearings are practically in your hand. So, if you need to do a front brake job, check the wheel bearings.

While you don’t absolutely have to do the wheel bearings on both sides at the same time (it’s not like rotors and pads), it’s generally considered good practice to do so.