Continuing to drive on a bad wheel bearing can lead to extensive and critical damage which will be significantly more expensive to repair than a simple bearing re-grease and service. And in the worst cases, the damage from a faulty bearing that goes untreated can prove impossible to fix, particularly if it contributes to corrosion of surrounding components and the axle.

Front axle nuttorque specs

You can still drive with a bad wheel bearing, but we wouldn’t recommend it for long distances. Keep your mileage to a minimum and look out for worsening symptoms of a wheel bearing fault; we cover the symptoms to check for later in this guide.

Typically, wheel bearings have a lifespan of around 85,000 to 100,000 miles, so if your car is approaching these kinds of figures, it’s important to keep an eye on the tell-tale signs of a bearing in decline.

Suspect that your car is suffering from a faulty wheel bearing? Our guide can help you check and diagnose the problem, and decide if and when it’s still safe to drive.

Frontwheel bearing hub assembly torque specspdf

Given the damage that can occur as a result of a failed wheel bearing, not to mention the dangers, this further reinforces the importance of getting those bearings checked and repaired the moment you realise there’s a problem.

As you’ll know from our car maintenance glossary, bearings allow the wheels to turn freely without generating huge amounts of heat. If a bearing were to fail, the wheel can seize up altogether, resulting in catastrophic damage and the potential for a serious incident. Indeed, in the very worst-case scenario, a failed bearing can cause the wheel to rip away from the car entirely.

Wheel bearing torquechart pdf

Confident in car maintenance DIY? Lubricate and service your car’s wheel bearings with Holts Multi-Purpose Lithium Grease. Trusted by professionals, it reduces friction and wear in all moving parts, even those that work under extreme pressure. For more top tips and advice, read the Holts blog or visit our help and advice centre.

Wheel bearing torquechart

If you’re aware that there’s an issue with your car’s wheel bearing, it’s best to take it straight to a mechanic for a full diagnosis and repair. Often, it may just be a case of relubricating the ball bearings within the assembly before repacking them, which is significantly simpler to put right than the alternative.

Replacing all of your car’s wheel bearings might cost an eye-watering sum, but it’s guaranteed to be a lot cheaper than repairing the damage should a bearing fail.

The cost of a wheel bearing replacement in the UK is roughly £150-£300, dependent on the make and model of your car and a mechanic’s labour costs. The good news is that you don’t need to replace all wheel bearings at once if the other three remain in a safe and serviceable condition.

Axle nuttorque specschart

Rearwheel bearing hub assembly torque specs

Need to recap the signs of a failing wheel bearing? Here are the symptoms to watch out for while you’re driving, particularly when turning corners:

When the car is elevated and in place, take hold of each wheel in turn and wiggle it backwards and forwards, side to side. If there is any play in the wheel, it feels wobbly or loose, or an unusual noise accompanies some minor movement, then you’ve found the problem wheel.

Once you’ve performed this basic wheel bearing test, you should have a better idea of where the problem is. Then, it’s a case of diagnosing the front or rear wheel on the side in question.

To do that, you’ll first need to jack up your car so that both wheels are off the ground. We would strongly recommend using service ramps for this to ensure you can carry out the following checks safely.

Rearwheel bearing hub assembly torque specspdf

HomeGMCEnvoyDrivetrainBearing HubTorque SPONSORED LINKS Hub assembly torque specs needed SWEETIE1965 MEMBER2004 GMC ENVOY4.2L6 CYL4WDAUTOMATIC189,000 MILES I recently found out I had a worn hub bearing so I changed the entire assembly. Would you have the torque specs for the brake caliper mounting bracket and the brake caliper and the hub assembly? Thanks ahead of time. Thursday, August 19th, 2021 AT 4:37 AM 1 Reply SQM MECHANIC6,383 POSTS Hello, Here are the torque specifications: Brake caliper mounting bracket bolts :110 lb ft. Wheel Hub and Bearing Mounting Bolts: 77 ft. lbs. Wheel Hub Bolt: 95 ft. lbs. Wheel Speed Sensor to the Wheel Hub and Bearing Mounting Bolt 13 ft. lbs. https://www.2carpros.com/articles/brake-caliper-replacement https://www.2carpros.com/articles/how-to-replace-front-wheel-bearings-and-seals Please let me know if you need any other info. Thank you. Images (Click to make bigger) SPONSORED LINKS Was this answer helpful?YesNo Thursday, August 19th, 2021 AT 6:23 AM Please login or register to post a reply. Related Bearing Hub Torque Content2002 Gmc Envoy 4 Wheel DriveGood Morning: My 4 Wheel Drive Lights Are Not Functioning, Nor Is The 4 Wheel Drive. I Have Looked In The Owners Manual And There Is...Asked by therrington · 1 ANSWER2002GMC ENVOY2000 Gmc Envoy 4 Wheel DriveWill Not Come Out Of 4 Wheel Drive Back To 2 Wheel Drive. Is There A Way To Do This Physically?Asked by TomJeffords · 1 ANSWER2000GMC ENVOY2002 Gmc Envoy 4 Wheel DriveMy 2002 Envoy Fails To Shift Into 4 Wheel Drive.Asked by lvert · 1 ANSWER2002GMC ENVOY Sponsored links Ask a Car Question. It's Free!SPONSORED LINKSWheel Bearing Hub ReplacementBearing Hub ReplacementHow to Replace Wheel Hub AssemblyOnline car repair manuals Contact• Help• About• Privacy Policy• Terms & Conditions © 1999 - 2025 2CarPros, Inc.

If you suspect you have a wheel bearing fault but aren’t sure which side of the vehicle is affected, there’s a safe and simple test you can use to check. Our step-by-step guide below can take you through how it’s done…