Toyotawheel bearingreplacementcost

Bearing Cross Reference ; Smalley Part #, Bearing O.D. (mm) · Small ; SSB-0035, 9, 603, 684 ; SSB-0039, 10, 623 ; SSB-0043, 11, 694, 685 ; SSB-0047, 12, 604 ...

Bearing housings are typically made of materials such as metal, plastic, or composite, and they come in various types, including pillow block, flange, ...

Not necessarily. I had this setup on my old Mazda Protege. You press the hub out of the bearing, and the inner race of the bearing is stuck in the hub. You then carefully score the outside of the inner race, and strike it once or twice with a chisel…the inner race splits in too, and you’re left with the hub, which you can press into the new bearing.

Oct 25, 2022 — It does sound like wheel bearing. Is your spare tire duratrac as well? If not replace on the front wheels and see if there's a noise difference.

I thought sometimes they just replace the whole hub part is a little more but less labor. That price sounds high you need to get a second quote.

Scope of work as per the first shop was to “replace the left/front wheel bearing and press the new one”, that’s all they mentioned.

you can get the whole hub and bearing for like $150 , so your mechanic is telling you it is going to take him 5 hours to do the job on a bearing ?? I doubt it , i would run from that guy .

Wheel bearingreplacementcostNear Me

Combined bearing without inner ring-Type:Needle and ball bearings-- and.

Same with a guy I know in my area who passed away back in 2011. He BSed, cobbled together, hacked up, and in general screwed everyone over yet everyone within 25 miles of him praised his name to the mechanical heavens. Go figure…

Elantra has same bearing setup as Honda’s. A shop can lowball the cost and then have to replace more parts or remove knuckle to press out bearing. The bearing is pressed into the hub. So, assume the hub will be damaged or scored.image600×600 22.3 KB

You didn’t mention the year of your Elantra, but when I plugged in a 2015 into repairpal.com for an estimate, my local zip code brought up an estimate for $173-266 to change a single wheel bearing…you definitely need to get a 2nd and 3rd quote

Wheel bearingreplacement near me

I took my knuckle to a shop and they pressed out my bearing and he said hub was scored but he had 1 used. For $20. I tried to pay with my card and tech said hub was his and cash only. Had to run to atm for $20 cash. Bet tech had a few hubs in his toolbox. From other jobs?

Wheel bearingreplacement time

After I drilled out the defective sensor , I took a reamer to the hole. The shop that removed the other sensor (left front) was nice enough to let me go home without a sensor (I got one from an online Toyota dealer at a big discount). And my labor is free.

MA Eder · 2014 · 47 — ... turbine blades in order to gain insight into the driving failure mechanisms. A method based on the virtual crack closure technique (VCCT) is proposed, which ...

Thanks all, appreciate the help. I did call a second and third shop and was quoted $350 by one and $380 from the other. Both shops gave me their estimate, and when they then asked what I was quoted when it was diagnosed they said the shop I went to was notorious for extremely high prices and that $750 was way too high… I’m surprised since the first shop had great reviews.

Did you get an itemized estimate? If not, ask for one. Do that when you get a second opinion too. That way you can easily compare the two. Don’t tell the second shop what the other one estimated.

Wheel Bearing costAutoZone

They need to be tight due to the super tight tolerance on positioning for proper operation. I did some work recently and had to R&R an ABS sensor. Long story short, a thousandth made a huge difference in signal level. Too close and it rubs, too far and weak signal. Rust forming on the spacer was enough to cause weak signal…removing them required diligent care not to damage them…

13168. The State Fire Marshal may refuse to renew any license in the same manner and for any reason that he is authorized pursuant to Article 4.

Our range of pump models have a solution for you. Screw Pumps, Vane Pumps, Gear Pumps, Oil Barrel Pumps. 126 products.

RM2-2RS 3/8 V Groove Guide Bearing Sealed Ball Bearings W2X Vgrooved: Deep Groove Ball Bearings: Amazon.com: Industrial & Scientific.

Frontwheel bearingreplacementcost

May 13, 2023 — Perhaps the down comforter of soft failures is a bad wheel bearing. Loss of lubrication will cause them to wear, resulting in a rumble that ...

Enter a search term or item number or browse our catalog. Search Term. COTTERPINS_TH. Item Number: CP-116X2.

I paid $250 parts and labor for the front wheel bearing of my previous Toyota Corolla. It had to be pressed in also. They put in a Timken bearing and it didn’t take much time…around 45 minutes and I was out of there.Shop around because your estimate seems on the high side.

This website is owned and operated by Web Team Associates, Inc. Copyright © 2025 U-Haul International, Inc. All rights reserved. U-Haul International, Inc.'s trademarks and copyrights are used under license by Web Team Associates, Inc. Air-Cushioned Ride®

Jiffy Lubewheel bearingreplacementcost

This doesn’t include the cost of replacing one perfectly good ABS sensor that had to be destroyed in the process. (tech told me that the sensor would be in the way of the press, and they couldn’t remove it without destroying it. ). I believed him, as I replaced the ABS sensor on the other side a year earlier. It was defective. I too had to destroy the old one to remove it, as Toyota machined the hole too small. Talk about a tight fit! There was TSB about this, I believe.

You did the right thing by getting other quotes and as an aside, never give a lot of credence to online reviews. Some may be fake and in some cases people may have been robbed blind and simply do not realize it. Their car is fixed for double what anyone else charges so they’re happy with it all.

As always when in doubt you get a second opinion . It could be that this shop does not have the right equipment for the job or there is a lot of labor involved .

Dropped my car off at a mechanic to check into an issue I’ve been having (groaning in the front/left wheel). Turns out it is a wheel bearing that needs to be replaced and the mechanic quoted me $750 for the job, saying “the bearing needs to be pressed and it’s a fair amount of labor”.

Wheel bearingpartcost

Yeah, tight but not pressed in I had to pry mine out a fraction at a time, going around to keep it from getting jammed. Both GM and an 03 Toyota Camry. The GM had a penta-socket head fastener on one side and a pressed in “rivet” on the other. Still struggling to understand/justify the need for such hardware…

You should also verify how many wheel bearings they’re replacing. If it were me, I would go ahead and replace the bearing on the other side of the vehicle as well…chances are, it’s not far behind in terms of failure.

Cool. With that said, you really should consider getting the other one replaced at the same time…see if the shop will give you a break on the labor.