AltaAP6Pro

Locate the rotor faces and place them face down on the ground (the back facing upwards). Then take your new bearing and push its bearing greases into your casing.

Replacing wheel bearings is a piece of cake and can save quite a few bucks, guaranteed you ALREADY have all these tools at home:

AP6420

Yes. Since wheel bearings and brake rotors are aligned, failed bearings will loosen the brake rotors and cause violent wobbles.

Regular wheel maintenance schedules should include frequent wheel bearing checks; that has always been a rule of thumb. However, it is the cost to replace wheel bearings that gives people a headache, as they are uncertain whether these upgrades may give huge blows to the financial budgets.

AP6 shall manage entrusted funds through investments in private equity (unlisted assets) in accordance with the law governing the fund’s role and operations, Sixth Swedish National Pension Fund Act (2000:193). Fund assets are to be invested such that the requirements for a long-term high return with adequate risk diversification are met. AP6 is a closed-end fund as the management of illiquid assets with a long investment horizon means that it is not possible to withdraw liquidity on an ongoing basis in the same way as is done from other AP funds.

AP6PRO

While driving to mechanics is more convenient and also time-saving, feel free to replace the bearings at home if you already have all the required tools ready. Write me letters if any type of wheel bearing issues persist

The average pricing range can stoop as low as $107-$147 (DIY) to as high as $400-$1000 (mechanic) – depending on whether you prefer DIY procedures or mechanic supports.

Image

Lift the car off the ground with two jack stands. That way, you will find it easier to remove the tire for ball bearing replacements.

AltaAP6

Hence, I often try to save the cost of wheel bearing by fixing/ swapping only one bearing. It is much cheaper than simultaneous front/rear replacements (refer to the pricing section above) while still delivering impeccable performance.

In general, you may expect to invest $190 to $310 for parts associated with the rear bearing replacements. Meanwhile, the labor charges fluctuate from $250 to $400.

Mechanic experts will have specialized tools to help press out those old bearings for you. After the new bearings are pressed in, technicians will re-install the spindles onto the vehicle.

To save you hours of research, my team has compiled the average price range of some of the most commonly-asked cars. If yours does not make its way into this list, I suggest consulting your dealer or manufacturer.

AP6Sophos

Douglas Mercer is an automotive service manager with 12-year experience at Stockton Wheel Service, Douglas excels in addressing intricate tire and wheel concerns as plating wheels, straightening bent wheels, widening stock wheels, and precisely correcting offset and back-spacing…

Put your new bearings into the rotor’s back and apply some grease to the cavity’s interior. Next, install the new seals over the bearing before placing the new retaining nuts on their spindles.

AP6aum

Image

A wheel bearing is often stored within the disc brake rotors, meaning you have to pry the dust cap off to expose retaining nuts and cotter pins. A couple of pliers will be your trusted ally in such cases.

Not to mention, not everyone is familiar with the technical aspects of the vehicle; jumping blindly into it without proper research might end up costing you even more than it should have.

Technically, you can, but it’s extremely dangerous. Premature/ uneven tire wear, worn transmission, and even explosions are inevitable.

If you want to play on the safer side and replace every bearing, expect to spend between $800 and $1000 in total. Unless you are already covered by special warranty policies, the overall costs can be quite a blow for most vehicle owners.

Use a ratchet to unbolt brackets and brake calipers from the spindles. Once done, remove the calipers with a screwdriver.

AP6840E

Once gathering the required supplies, you should prep the car beforehand to ensure maximum safety. To begin, park the vehicle on an even, level surface.

Loosen them with a ratchet (1/2 inches) and proper size sockets. Remember just to loosen them; don’t remove the nuts completely yet.

Does the bearing stay flush against the spindle? If so, I suggest removing the spindles – then taking both the bearings and spindles to the nearest repair shop.

Now that the vehicle is safely secured and lifted, you can proceed to remove the nuts completely. Once done, pull the tires off and place them aside.

Block the tires opposite your chosen wheel using a chock. For illustration, if you change the front bearings from the driver’s side, then remember to chock the rear wheels from the passenger’s.

Ap6pension

My insightful guide, while not offering direct solutions to your budget-saving goal, can still deliver helpful advice regarding the cost and alternative replacement methods. Keep scrolling.

Image

There is no point in choosing to do it on your own if these tools have not yet been purchased; buying all of these equipment pieces in one go can be even pricier than having it done by auto mechanics.

Unfortunately, the front wheel bearing replacement cost is much more expensive than its rear counterparts. The average labor cost runs from $350 to $550, while the pricing for replacement parts is $150 to $300.