Have you been hearing a scraping, scratching, or grinding noise while driving or turning your car? Our mechanic shows you how to identify what’s causing that scraping noise coming from your wheel while driving in this article and video.

Grindingnoise when accelerating at low speed

A dust shield is responsible for keeping debris, such as rocks or water, from contacting or getting trapped on your rotor. It’s especially helpful in areas and climates where vehicles are prone to rust. For example, the dust shield minimizes large splashes of water that could contact your rotor so it won’t rust as quickly.

After gently prying the dust shield away from the rotor, go for a test drive to find out if the scraping noise has stopped. If it hasn’t, you’ll probably need to replace your rotor and pads.

Grindingnoise whendrivingat high speeds

Standard Combined Roller Bearings. Part Number, Bore Dia, Outer Dia, Dynamic Radial Load. WD053/52.5-2RS, 30 mm, 52.5 mm, 7 kN.

Essential 2017 Jeep Patriot Wheel Bearings · National – Ball Bearing (Part No. · Dorman – Left Loaded Steering Knuckle (Part No. · Driveworks – Wheel Bearing: ...

If you find that your brake pads and rotor look like they don’t need to be replaced yet, you can instead gently pry the dust shield away from the rotor with a flat blade screwdriver. That will prevent it from contacting the rotor until you do replace your brake pads and rotor.

Intermittentgrindingnoise whendriving

The SKF Bearing Tool Kit TMFT-36 is designed for quick and precise mounting of bearings, while minimizing the risk of bearing damage.

Jul 24, 2012 — The Bearing dimensions under these series conform to British Standard BS 292 : Part 2 : 1982. JK Pioneer deep groove Inch series Industrial ...

Grindingnoise when accelerating

Grinding while drivingbut not brakes

100/54 as a percent is 185.185%. Methods: Method 1 – Converting 100/54 Into a Percentage: First, let's go over what a fraction represents.

Safely raise your vehicle off the ground with a jack and jack stands so you can inspect the area where the scraping noise is coming from.

Inspect your brake pads’ thickness. Typically, brake pads are 8 to 10 millimeters thick. If you think the pads are too worn, you may need or want to replace them, along with your rotor.

Grindingnoise from front wheel whendriving

Grindingnoise whendrivingat low speeds

... Bearing, Honda Bearing, Yamaha Bearing, ball bearings, and flange bearings ... bearing suppliers. Our company has a foundation built on quality parts at a ...

Brakesgrinding while driving

KIT includes bearings, collars and inner and outer seals, KIT does one complete axle (left and right bearings and seals) Fits all 1979-1995 20R/22R/22RE/22RTE, ...

Free arm and extension table. Straight stitch and zig zag with length and width control. Needle 3-positions. Reverse, buttonhole. Bobbin winder, foot...

Shop for the best Hub Assemblies for your 2006 Honda Civic, and you can place your order online and pick up for free at your local O'Reilly Auto Parts.

My car makes a metal on metal sound when driving at high or low speeds. Sounds like front wheel are but hard to be certain. It comes and goes and pressing the brakes doesnt cause it or make it go away. All the brake components: pads, rotors, parking brake have been changed. In hopes that was the issue as my mechanic could not find what the cause was. It didn’t do it for 2 weeks after I got the vehicle back but is happening again.

Check your wheel bearings for any play, which may cause your rotor to shift and contact the dust shield. In this case, the scraping noise may be more apparent when you’re turning. You may also notice that your rotor’s edge has rusted unevenly because of that play.

Nov 7, 2010 — I have a loud grinding noise coming from the front of the car. I jack the front end up and grab at 12 and 6 on both wheels and there is no play.