Never reuse any wheel bearing (sealed or tapered) that’s loose, worn, noisy or shows any signs of wear. Trying to fix a loose or damaged wheel bearing can result in an accident and severe injury. Even if a pro suggests repairing a bearing, don’t let them.

2014gmc yukon wheel bearing replacement cost

The average cost to replace a sealed wheel hub bearing is around $350 per wheel. However, depending on the make and model, the shop labor rate ($47 to $215 per hour, according to AAA) and any additional damage could push the cost beyond $1,000 per wheel.

202434 — Common Symptoms of a Failing Wheel Bearing ... While you may not be able to immediately visually identify a faulty wheel bearing based on its ...

2007gmc yukon wheel bearing replacement cost

Older rear-wheel-drive cars or trailers use a set of two tapered roller bearings that face each other. These should be routinely serviced every 20,000 miles, or once a year.

We are no longer supporting IE (Internet Explorer) as we strive to provide site experiences for browsers that support new web standards and security practices.

NOTE: Whether you DIY or your mechanic replaces the bearing, always install a new axle hub nut. Most hub nuts are prevailing torque fasteners. They’re used on critical components, like securing axle shafts to hub bearings, where a loose nut could lead to disastrous consequences.

Download the latest drivers, firmware, and software for your HP LaserJet 1320 Printer series. This is HP's official website to download the correct drivers ...

2012gmc yukon wheel bearing replacement cost

2018gmc yukon wheel bearing replacement cost

This work would be done in Southern California. I’m always skeptical of car repair quotes, so does this seem like a rip off?

Under normal driving conditions, wheel bearings should last 85,000 to 100,000 miles. They can fail for several reasons, including:

Damage to the wheel bearing becomes noticeable after some time through noises that can increase or decrease depending on the driving situation.

2017gmc yukon wheel bearing replacement cost

I have a 2012 Chevy Malibu with 130k miles that started making a high pitched squeaking noise towards the front right part of the vehicle. Took it to the shop and apparently need a front wheel bearing replaced.

L44643 RUBIX clearance, 132709 1032710 New Holland JD8253 JD8933 John Deere clearance, NTN 4T L44643 L44610RS Tapered Roller Bearing Cup and Cone Set 1x1.98x0.

It is made by Enduro, which is known worldwide for top quality bearings. It is manufactured in South Korea. Large quantities are available.

2013gmc yukon wheel bearing replacement cost

On modern front- and four-wheel-drive cars, wheel bearings are a set of permanently sealed, precisely machined steel ball or straight roller bearings. The balls or rollers are encased in a “cage” that supports the bearings, allowing them to rotate freely.

The mechanic recommended I do both front bearings to save on labor down the road. To remove and replace both front wheel hubs and bearing assemblies, I was quoted $567 for labor and $497 for parts, so $1,064 total.

Tool for tapping out small bearings that have an inside dia between 2 to 14mm. Fits inside dia of 2mm, 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm & 14mm.

In my 50 years in the auto repair industry, I can’t recall one good story about wheel bearings. Most involve some sort of brake system failure, tires exploding, or fire from a seized red-hot bearing igniting axle grease. Bad wheel bearings should not be ignored.

I’ve replaced hundreds, if not thousands, of wheel bearings. One thing I’ve learned: A bad wheel bearing always gives an indication it’s failing. These include:

My opinion? If your vehicle has more than 50,000 miles or has been driven in harsh conditions, then it’s logical to replacing wheel bearings on both axles. However, if your vehicle has low mileage and the other bearing is in good condition, replacing only the damaged bearing should not be a problem.

Choose from our selection of feeler gauge sets, feeler gauges, and more. In stock and ready to ship.

The cage and rollers are held together inside a hardened metal ring called a “race.” The seal keeps grease in and damaging water and debris out. Wheel bearings are installed inside, and secured to, the suspension, either by press-fit, bolts or a snap-ring. Once mounted, the wheel bearing rides on the axle shaft, allowing the tire/wheel to spin effortlessly.

2016gmc yukon wheel bearing replacement cost

Wheel bearings allow cars and trucks to run smoother and more efficiently by reducing friction and supporting vehicle weight.

Driving on a bad or failing wheel bearing is dangerous. If ignored, it can quickly turn into a safety issue and an expensive repair.

2008-2012 Chevrolet Malibu ; 2006-2007 Chevrolet Malibu, Rear: Disc ; 2004-2005 Chevrolet Malibu, 4-Wheel ABS ...

FAG 24152-BE-XL-C3. 2024-05-24 17:31:58. ￥13604.27. . 107. 260mm440mm180mm

Adtech Spirent 400120 AX/4000 Portable 16 slot chassis | Adtech Spirent 400120 and other used Telecom & Utilities, Digital Telecom from Adtech Spirent for ...

However, on some vehicles, it can be less than $100 per wheel. And you can save hundreds in labor if you DIY. If you don’t have the tools, most auto parts stores will lend you the specialty tools and equipment needed.